Bill April 12, 2020 for Model Number FES367ASB I need to replace the broiler element. Mine is broken in two. The video shows screws holding up the front of the element. Mine has two wire hangers similar to what you hang Christmas ornaments with. What is the correct part number I need? Thank you. Bill
1 Answer Bill,Based on the model provided the part number for the broil element is correct 318255605 (The videos are not model specific, just general application) Read More...
Patrick September 18, 2019 for Model Number RE20W I need a new broil element for a Summit 20-inch electric range oven. I didn't see the specific brand, but I want to know if there is a similar part from APP which might fit the same model?
1 Answer Hello Patrick,unfortunately, appliance parts are model specific, we do not have a size cross-reference to go by. Read More...
Donna December 23, 2017 I can't get the clips off the old broiler element they don't slip off as easily as shown in vide bano
1 Answer Donna, If you are referring to the wire terminals then you would grab hold of them with needle nose pliers and pull them off. Read More...
Larry November 02, 2016 for Model Number westinhouse HO Q53350 Old Vintage wall oven and the heating eliminate was replaces some time ago but never worked properly ever since, not sure if the proper heating eliminate was purchased so going to start there. needed to know the proper heating eliminate that came with the stove and other possible reasons for not heating properly. Thank you Larry
1 Answer Hello Larry. The model number you provided is to old to locate in the data base. Without a diagram we can not provide you with the proper part number for the correct element. Sorry about that. Read More...
Bwrubac May 06, 2016 for Model Number RS-10J I have a 1964 or 1965 Frigidaire Super range/oven. I'm looking for a part number for a replacement bake heating element. Thanks.
1 Answer BWRUBAC, Your range is a 1965 production model number. Surprisingly the bake element for the oven is still available. The part 5309950887 / 5309950887 Bake Element, is in stock and available at this time. Thanks, Read More...
Kim January 15, 2014 for Model Number EOYKLV-50 I have a Youngstown Tappan Visualite 24" wall oven. It was working when a remodel occurred 7 years ago and put in storage. In trying to install it recently and testing it...it does not heat. There is power and the oven light comes on. Another issue...is the door seems sprung a little from storage. Please advise with where to start in diagnosing problem and if replacement parts are available. This oven was probably originally installed in 1959. It is all stainless. Serial # is H 18612 Thank you for your assistance!
1 Answer Hello Kim. Check all wiring and connections. Make sure there is 240 volts coming to the unit. The hinges are no longer available. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Ken November 27, 2013 for Model Number PLEB30T8CCB My upper oven does not heat on broil or bake but convection fan will run. Both elements tests at 22 ohms. The lower oven will bake but not broil. The upper element tests at 22 ohms. What should I look at next ?
1 Answer Hello Ken, This sounds like bad relays on the control boards 318022002 and 318022001. I would verify 240Vac to the elements. When you see that the voltage is not present, (I am suspecting you will only find 120Vac), turn th3e power off and remove the wire from the control to the element. Turn the power back on and set to the appropriate setting for the element you are checking and if you are not getting the voltage from the board, it has failed. The same procedure applies to each of the elements. Read More...
Mary November 18, 2013 for Model Number ffef4017lb I need a bake element for the small oven. Do you have any? It is a 40 inch Frigidaire Range with the griddle on top in the middle.
Steven October 02, 2013 I need to know if I can get a cross reference part for a youngstown tappan wall oven. I need the bottom heating element.
1 Answer Hello Steven. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Ray March 13, 2013 for Model Number 790.99513307 Broiler does not heat. Element resistance 22ohms. Both relays cheek out ok. I have 240 volts across broiler relay on the control panel. Do you have suggestions?
1 Answer Hello Ray. If you test at the element, and there is 240 volts, but the element does not heat, you will need to order and replace the element in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...