Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Control Timer by Frigidaire

Best Seller
Manufacturer Part
4.89 (64)
By: Frigidaire
Part Number: OEM6324246
Manufacturer Part Number: 134049500

Fix a washer that won't advance cycles or gets stuck in one mode. This control timer manages wash, rinse, and spin timing. 30-minute DIY repair.

More

Questions & Answers

For Frigidaire Washer Control Timer (Part Number: OEM6324246)

1 Answer

Rickey,

With the unit not going into agitate but will go into spin and drain, the issue will most likely be caused by a faulty timer. The part number for the timer is 134049500.

Read More...

1 Answer

Ron,

In most cases when a unit starts agitating immediately, the issue will either be a clogged pressure hose or a bad water level switch.

Read More...
Mike for Model Number glws1349as1 frigidair washer

The washer fill cycle and wash cycles work fine. The drain cycle will not start the pump. I tested the pump and it works fine. I tested the pressure switch and it seems to work fine. I bypassed the pressure switch to make the pump think it was full. No voltage signal gets to the pump. The only thing I can summize is the timer cam is bad for cycle 4. The timer makes a clicking noise when in the rinse/spin cycle. The timer motor runs fine but, I manually move it with the lid switch down and no signal get to the pump motor. Is there anything else that it possible be besides the timer switch?

1 Answer

Hello Mike,
Judging from the tests you have made and the results you have made, I would have to agree with the timer 134049500 being the issue.

Read More...

1 Answer

Hello Mark. Yes, based on the information you provided, it sounds like the timer is bad and will need to be replaced on the unit.

Read More...
Dave for Model Number GLWS1339EC0

My washer completes a wash cycle, but will not drain or spin. The timer seems to advance to the drain position, then everything stops. I can't even get it to drain by manually advancing the timer. I've tried all of the locations on the timer dial where is should drain ... nothing at any of them. This seems to indicate the drain pump, but I've taked the drain pump out (oh, what a joy that was), and applied A/C power directly to it ... and it spins. I put the drain pump back in ... no joy. Any thoughts? Timer?

1 Answer

Hello Janet. If you can manually advance the timer and it works, then you will need to replace the timer 134049500 on the washer.

Read More...

1 Answer

Hello Jay. Based on the information you provided, it sounds like the machine is siphoning out. You will need to check and make sure there is only 6 to 8" of drain hose inside the drain pipe. Also, make sure the drain pipe is not backing up and the pipe is not air tight around the drain hose. Hope this helps.

Read More...

1 Answer

Hello Christian. If you can provide your model number, we will be glad to help you on this. Thanks.

Read More...

1 Answer

Hello H. You will need to remove the back cover on the control panel and gain access to the timer. Then remove the knob from the timer and release the tab holding the timer in place. Slide the old timer out of the unit once the tab is released and unplug the wires going to it. Reinstall with the new timer in reverse order. Hope this helps.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google