Steve M January 07, 2026 for Model Number will 134049500 replace 131758600B on a frigidaire combo washer dryer ? will timer 134049500 replace 131758600B
1 Answer Steve, The part number 131758600B does not come up as being a good part number. If you can supply the model number we can locate the correct timer for this unit. Read More...
James January 31, 2023 for Model Number Kenmore 417.93862200 None of the cycles (Normal/Delicate/Perm Press) will start, but if I "start" the cycle at any of the rinse/spin the washer turns on and starts filling up with water. From what I read, this will likely require the replacement of the Timer (part 134049500). Does this sound about right or could there be another issue?
1 Answer James, If the water setting for the wash is set for warm or hot then check to ensure that the water valve is not clogged with sediment. If this is not the case then the issue will most likely be with the timer. Read More...
Keith January 19, 2020 for Model Number GLWS1349AS1 I am about to give up. I have a squeal only on spin start up. From everything I read on your website, it seemed to be obvious. It was not the motor, spin bearing, pulley, or the transmission. I took this repair way too far but am at the point of no return. I took voltage readings at the motor plug while connected and in spin mode to the white wire. Red and purple was 120V, Gray was 20V which is really odd to me. Seems that gray should be 120V as well. Minor voltage on the B/R and orange. Something is leading me to the timer. I also notice a circuit board in there. Any thoughts?
1 Answer Keith, the belt 134511600 would need to be inspected for dry spots or sections worn out more than normal as this can cause the issue described. Read More...
Jack March 17, 2019 for Model Number GLWS1439FS1 Frigidaire Model GLWS1439FS1 top-loading washer stopped spinning and agitating, found that the lid switch/lock failed, it was partially melted and had an electrical burnt smell. I replaced it with a new #134101800 lid switch/lock assembly. After installing the new switch, the washer was started and the problem appeared to be fixed, but a little later there was a smell of burnt electrical and you could see smoke coming from the new lid switch/lock assembly. Question is, what would cause a lid switch/lock to overheat and burn up.
1 Answer Jack,Your problem is most likely the capacitor, you can also test the motor windings with the tech sheet. Read More...
John February 06, 2018 for Model Number NMWS336FS1 When the washer is filling up with water the hot water solenoid does not work. I pulled the plug off and get 120 volts ac. When I plug it up to the solenoid the voltage drops out. I can put the cold water plug on the hot water solenoid and it works. I trace the voltage drop coming out of this timer knob. The 120 volts ac comes from this timer knob and goes through the temperature selector knob and then to the solenoid. Have you seen this before?
1 Answer Hello John. See if your voltage is dropping at the timer or the temp switch. If the timer, then you will need to replace the timer. If the voltage drop is the temp switch, you will need to replace it. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Lwats November 02, 2017 for Model Number 41793802200 It takes a very long time to dry clothes. Plus the temperature seems to be the same no matter what setting you have it on. This has been going on for quite some time. What's causing this and needs replaced?
1 Answer Lwats, The first thing that you will want to do is to make sure that the vent is not clogged or restricted. If this checks ok then the most likely cause will be temp switch that may be faulty. Read More...
Lwats November 02, 2017 for Model Number 41793802200 My washer goes through its complete cycle and then the timer continues clicking until it starts the extra rinse cycle. This is a total waste of water! Does the timer need replaced?
1 Answer Hello Lwats. If there is no option to turn off the extra rinse, and this just started happening, you will need to replace the timer for the washer on the unit. Read More...
Mike D. June 23, 2017 I have the timer, 134049500. The white plastic stick piece that sits inside of where the knob is attached broke and fell out. Is there a way to purchase just that piece?
1 Answer Hello Mike, I'm sorry but the complete timer 134049500 has to be replaced if the timer shaft has an issue. Read More...
Scott October 28, 2016 for Model Number Frigidaire gallery, 13 cycles commercial hy duty 2 sp motor I have the top of washing machine off with the timer still connected to the face. The video shows needle-nosed plyears (computer's spelling) used to hold timers shaft to remove it but on my unit there is no room for plyers to grab it. What's the secret? I might break something if I pull out the knob too hard. Timer part #134049500
1 Answer Scott, If you get a small blade screwdriver in the opening and lift up then the pin will lift and allow the knob to be removed. Read More...
Kirill October 16, 2016 for Model Number MEX731CFS0 The washing cycle on my laundry center MEX731CFS0 stops in the mid of the cycle. The drum stops rotating and I hear hum from the machine. The lid is locked. To continue the cycle I have to manually advance the timer (to turn it a bit further clock-wise) and the cycle continues. Do I have faulty timer (Timer Elec H Mallory-Delta)? Thank you.
1 Answer Kirill, This issue would most likely be stuck contacts inside the timer that is sending a mixed message to the motor 131964100. Read More...