Tonyq March 08, 2024 for Model Number 41797922701 Kenmore laundry center My washer is not draining in wash cycle, timer keeps running passing the drain cycle and it would start the spinning cycle dumping all the water out on the floor, but drains normally when in rinse and spin cycle , would this be a timer problem ? It started it doing it occasionally but now is doing it almost all the time Thanks
1 Answer Tony, based on the information provided, the timer 134237200 is the most likely cause of failure. Read More...
Bea January 28, 2021 for Model Number model 417.97812701 Hi, my laundry center won't agitate but it will fill w/water to the correct load, it will drain and it will spin. When its on the wash cycle and the water has filled, it won't move at all and there is no sound, it sounds as if it was off. Checked the agitator it all looked fine. Checked the belt and it looked fine. Heard it could be the Timer so I bought one on E-bay, big mistake cus they sent a used one and I put it on my washer anyways but there was no difference. I don't know if it was the part or if its just not the Timer. I'm past frustrated as you can probably already guess. If you could help me by pointing out what could be the problem I'd really appreciate it.
1 Answer Bea, With the unit not agitating it would be best to see if there is 120 Vac to the motor when the unit should agitate. If there is not then this will likely be a wiring issue that will need to be corrected or a faulty timer. Read More...
David D December 14, 2018 for Model Number AP3220654 How would I find the date code or even the serial number for this part?
1 Answer David, Unfortunately, the manufacturer does not provide that information to us. Read More...
John March 02, 2015 for Model Number Frigidaire Washer Dryer Combo GLET1142CS0 I suspect it is the timer but want to make sure. Washer fills up and washes but when it gets to the rinse and spin time it stalls. When it stall there is 120 volts on all pump and motor connections. I figured there is a neutral not making up in the timer control. Is there anything I can check with meter to verify. 134237200 is part number. Its $140 so I want to make sure it is not anything else
1 Answer John, It sounds like a contact in the timer is sticking. If there is power to the other components but will not advance this is the most likely cause. Read More...
Steve October 15, 2013 for Model Number 417.94862302 The washing machine on this kenmore stackable will not agitate at all and only rinses and spins if I advance the timer manually. I already replaced the timer twice on your advice but the problem continues. What else could the problem be?
1 Answer Hello Steve. Check and see if the motor is running during the agitate cycle. If so, and the unit does not agitate, it is the transmission. If the motor does not do anything, it could be the pressure switch, or the wiring harness on the unit. You will need to check and see where your losing power at. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Cindy September 07, 2013 for Model Number Frigidaire Affinity BAFW 3574KWO My front loader stops with 12 min. left to complete the cycle.
1 Answer Cindy, Check and make sure the cold water faucet is opened and on. Then disconnect the cold water hose, and check and clean the debris screens in the hose and in the water valve inlet. If there's little or no cold water to the fill valve, the washer will stop at the rinse cycle. Read More...
Joe Herbert December 09, 2012 for Model Number 417-94862302 We have in our 158 unit complex Kenmore combo 417-94862302 and the dryer's timer gets stuck on any cycle, anywhere I set it to will not move, dryer keeps running till I stop it manually. I have replaced the timer and still doing the same problem. What can I check and replace next? Thank You!
1 Answer Hello Joe, You will want to check the tan wire from x on the timer motor to the pin 5 on blower motor. Look for the wire to have continuity. If no continuity then the wire needs to be replace. If it show continiuty then the timer would be at fault. Read More...
1 Answer Ridrigo, You will need to use a small flatblade screwdriver to unlock the retaining shaft at the back of the timer assembly " Timer Knob (some models) The timer knob is held on the shaft by a locking rod that extends to the rear of the timer. To remove the knob, disconnect power, remove the rear panel of the console and using a small screwdriverpull the locking rod backward to release the knob." Good Luck and Thanks Read More...
Carlos May 19, 2011 for Model Number part 134237200 timer My washer only works on rinse and spin cycles. What could be the issue?
1 Answer Hello Carlos. From your description, it sounds like you are experiencing a timer issue. We will need the model number and serial to provide you with the correct timer for your unit. Thanks! Read More...