Robert Carucci October 25, 2012 for Model Number JK2904BC GE Wall Oven I need to replace the BAKING element in the unit. I took the model# from the plate on the unit (S/N RDY59692) but unable to find a match. Can you tell me the P/N please, thanks.
1 Answer Hello Robert, you bake element is part# WB44X200 and your broil element is part# WB44X173 is case you need it. Thanks! Read More...
Sam November 10, 2011 for Model Number WB44X169 Hi. I try to replace it but it has different set for the temperature switch . The old one has a clip pate . How do I do it?
1 Answer Hi Sam. Remove power. Remove the oven rack. Unbolt the bake element and unhook the wires. Reinstall the new element and pull out the unit. Remove the back and insure the wires are hooked tight. Then it is important to repack the insulation around the back of the oven cavity/ @ element exit holes. This will prevent any more heat escaping and burning of wires. Thank You. Read More...
Anna E. September 26, 2011 for Model Number jk19010av Looking for heating element (baking) build in oven year about 1973.
1 Answer Hello Anna! The bake element used on the given model is part number WB44X169. Thanks! Read More...
Hank September 11, 2011 for Model Number JK140R3BC Is the bake element for GE model JK140R3BC still available, or is there an acceptable substitute for that element?
1 Answer Hello Hank! The replacement bake element used on your GE model JK140R3BC is part number WB44X200. Thanks! Read More...
Janet June 06, 2011 for Model Number jk1405av Do they still make heating elements for this oven model, JK1405AV?
1 Answer Hello Janet! The bake element for your model is WB44X169. I hope this info helps! Read More...
Chris M March 25, 2011 for Model Number JK2903 AV Thanks again for responding. This is an 1969 GE oven. The sensor unit does fit between the rear prongs. I noticed that one person had been able to force the sensor in the 1" space but I cannot see how that can be done without bending the element prongs. Also the prongs on the original are 3 1/2 " (not 2 1/2) so that the sensor was very close to the terminals. The sensor was mounted without the clip that originally held it in place.
1 Answer Chris, Our Reaseach Team has exhausted all of it's data. We will need to contact the manufacturer in order to acquire the part(s) you need. Could you supply us with a photograph of the Production tag on the unit, and part(s) you require. Could you please supply us with a contact phone number, so we can make arrangemenets for an email address. Your cooperation is greatly appreciated. Thanks Read More...
Chris M. March 25, 2011 for Model Number JK2903 AV I recieved your answer to my question as to the needed space between the rear prongs needed to fit the temp sensor between them. A 1 1/4" space is needed as with the original (1 1/2" center to center.) I was told by your company that the unit in stock has only a 1" separation that will not accomodate the sensor. The prongs would have to be bent or the sensor mounted differently. If you , in fact, have the unit with a 1 1/4" separation (actually measured) I would like to order it. Please help. Thanks.
1 Answer Chris, are you certain you supplied the correct model number? We have researched all the oven cavity parts for the model number you supplied. We cannot find a oven temperature sensor or a bake or broil element that is configured the way you're describing it. Could you verify the model number again, please. Our information indicates, the oven temperature sensor in located in the upper left corner of the back wall of the oven cavity. Neither of the elements, bake or broil are configured to accept any type of mounting device. Thanks again. Read More...
Chris M. March 23, 2011 for Model Number JK2903 AV The bake unit WB44X169 need to be replaced. The unit available Part #AP2031019 has a 1" space between the two prongs benind the mounting plate and so the temperature sensor will not fit between them. The original unit has 1 1/4" space (1 1/2 center to center.) What do you recommend? Can the prongs be bent to fit or can the sensor be mounted elsewhere?
1 Answer Hello Chris! WB44X169 is the correct part number. Our picture may be of an older WB44X169 element. This will fit on your appliance model JK2903 AV. Our part number is WB44X169. Thanks! Read More...