Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Control Board by Ge

Best Seller
Manufacturer Part
4.89 (64)
By: Ge
Part Number: OEM11022531
Manufacturer Part Number: WH12X10271

Questions & Answers

For Ge Control Board (Part Number: OEM11022531)

Chuck for Model Number WARE5260D1WW

After I push the start button on the washer, the tub starts to fill up then stops. I hold the button for a minute or two, and let it go, it fills up. It goes into the wash cycle, then will stop,and after I restat it, it continues to do this. It seems like it stops in between cycles. Other times the washer goes through all the cycles with no problems, then will work intermitently the next load I do. I thought this might be a control board problem, but dont want to spend the money on a panel if is not the problem. Thanks

1 Answer

Hello Chuck,
You need to unplug and reconnect each connector three or four times. This tends to remove corrosion from the electrical connections. If doing this does not help, the most likely issue will be the control WH12X10271.

Read More...
Sarah for Model Number WNSE5260D0WW

Our washer works great sometimes, then it seems to just stop randomly throughout the cycle. Sometimes it stops as it is filling up before I even close the lid...sometimes it fills and stops (and sometimes appears to start the entire cycle over when I hit the Start button to get it going again) and other times I don't believe it does the full spin cycle so I do just a Spin cycle and it's fine. But I'd like a suggestion as to what might be the problem. I thought maybe a new control panel would do the trick, but didn't want to spend the $$ unless I had an expert opinion! Thanks a bunch!

1 Answer

Hello Sarah,
As per the tech sheet for your model, before replacing the control, first dis-connect and re-connect all connectors to the circuit board. The other end of the connectors should be checked also. The connections should be checked in case a bad connection is causing the complaint. This actually sounds like a connection problem.

Read More...

1 Answer

Hello Craig,

You will want to check the pressure switch hose for clogs or being kinked. Also check the drain pump to make sure that there is no clogging and that the vanes are in good condition. The drain being clogged would not allow unit to spin if there is water in the unit that is causing the pressure switch to stay closed.

Read More...

1 Answer

Hi Juanita. Dis assembly – Control Panel. ?? To remove control panel, remove screws, then pry out on each side to release tabs,
then tilt forward & to the right. Control panel part # WH12X10271. Remove front knobs. Make sure that you have removed body static by grounding yourself first on bare cabinet metal.Do this a few times over and over. Try to touch only the outside corners so static does not inject into the board logic controls. Then mark all wire connections before removal so you insure proper installation. Use a cell phone picture if needed. The wiring diagram is supplied in the same area if needed for quick reference. Reinstall in reverse procedure. Thank You.

Read More...

1 Answer

Hi John. You will need to replace the control board part # is WH12X10271.Also check your water valve inlet screens to clear all debris from the inlet screens for proper filling. Thank you.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google