Vonn November 17, 2019 for Model Number kenmore 363.9542613 part # WR02X8676 shows no longer available from manufacturer. is there anywhere else I can obtain this part from? ( doesn't have to be original equipment, an after market part would be ok )
1 Answer Hello Vonn,if the manufacturer has discontinued the part, then it is out of stock and no longer available, there is no substitute that will work. Read More...
Andrzej August 31, 2018 for Model Number GE My refrigerator stopped dispensing water and or ice. No light in dispensing place either. It blew a fuse in the fuse box. I replaced the fuse and the refrigerator started working. Ice is produced but not dispensed. Ordered new switch and is on the way? Did I do it right?
1 Answer Hello Andrzej, This could be the cause of your problem but for a proper diagnosis, we would need to ask you to please post a new question including the model number from the units' I.D. tag. This will enable us to pull up valid parts numbers and the configuration of your unit. Thank you for your patience and understanding in this matter. Read More...
Greg December 29, 2016 for Model Number TFX27PPBAWW It is a GE Profile series. Currently dispenses water. Move selector for crushed ice and push dispenser switch, nothing happens. Move selector for cubed ice and push dispenser switch, loud thunk from the solenoid, an urrrh noice but nothing happens. Can manually turn auger motor, so would think it is frozen.
1 Answer Greg, In most cases this issue would be caused by a faulty dispenser control board. The part number would be WR55X129. Read More...
Tim S December 27, 2015 for Model Number TFX25PRYDWW When you press the tab to get ice or water it continues to dispense even after you release. almost like it is sticking open.
1 Answer Tim, You will want to check the dispenser switch to make sure that there is not an issue with the switch sticking. If this checks ok then the control board WR55X129 would be the issue with the unit. Read More...
Bassman August 04, 2015 for Model Number ge profile refrigerator zfsb27dagss the ice dispenser is only dispensing crushed ice, regardless of whether the selector switch is on crushed or cubed ice.
1 Answer Bassman, With the unit only dispensing crushed ice you will want to check the crushed/cube solenoid which is located beside the auger motor. This is the most likely cause for this issue. Read More...
Jim Y. July 29, 2015 for Model Number TFX27PRXBWW The water has quir dispensing. The ice dispenses ok and the ice maker still works. I replaced the water valve and still no water. We did have the switch stick a couple of times which cause the water to continue to flow. I know the the valve is working with plenty of pressure. Could it be a faulty dispenser switch or control panel?
1 Answer Hello Jim. Yes, the dispenser switch may be bad and need to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
David H May 11, 2015 for Model Number TFX22ZPBEAA Water dispenses fine but have to play with switch to get crushed ice. Cubed ice does not dispense at all, just a hum. Is dispenser board at fault? Thanks in advance.
1 Answer David, The dispenser switch would most likely be the cause for having to jiggle the switch to get crushed ice and there not to be any cubed ice. Read More...
Jiji April 20, 2015 for Model Number GSH22KGPC Water/ice dispenser panel is switchy but most often it defaults back to the cube ice choice and stays stuck there for a few hours. Sometimes we get lucky and it lets us select water and stays on water until someone select ice then it would stay stuck at ice for a few hours. Is it a micro switch issue or a control board's? thank you.
1 Answer Jiji, This issue would be caused by a faulty dispenser control board. The key for the ice is sticking and the control would need to be replaced. Read More...
Dave B March 19, 2015 for Model Number TFH24PRSMAA Ice and water dispenser is not working same with auto light or light switch on door. It started with solenoid smelling and falling apart on back of ice tray. Would still dispense water and mix of cube and crushed ice then all stopped. Still makes ice, already replaced solenoid.
1 Answer Dave, With the issue that you are having, the most likely cause for this would be the dispenser control board part number WR55X129. Read More...
Mike March 01, 2015 for Model Number GSS25IFRFWW When pad is pressed, light comes on, but does not dispense water or ice.
1 Answer Hello Mike. You need to make sure the dispenser is not locked out. If not, then test the micro switch in the dispenser. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...