Herman October 25, 2022 Does spark igniter wb13k18 pull out or is there a hold spring under range top
1 Answer Herman, if the model number of your appliance could be provided in a new post, this will allow the most accurate information to be presented. Read More...
Kurt September 18, 2020 for Model Number AP2020568 Does the AP2020568 item come with an attached wire. It's not shown with one. The wires on my unit are old and they need to be replaced as well.
James June 09, 2020 for Model Number JGP636BEV3BB We have a GE gas range (JGP636BEV3BB) and we hear periodic clicking when the range is not on. I was planning on replacing the igniters (WB13K18) and the wiring harness (WB18K5465) as one of the wires appeared to be charred. However, I cannot find the wiring harness anywhere and have been told by GE that it is no longer being made. Are there any options for the wiring harness that would work?
1 Answer James, Unfortunately, with the wiring harness having been discontinued there would not be a suitable replacement we could recommend. You could get some high temp wiring and connectors and make your own if these are the ones for the igniter that you are wanting to replace. We do not carry the connectors that would work for that but the high temp wiring would be part number TJMA0514G. Read More...
Shantilal June 01, 2020 for Model Number GE,gas renege, JGBS23WEW1WW ALL 4 BURNERS ARE CLICKING/SPARKLING ALL TIME. WHAT PARTS I NEED? HOW I CAN DO ?PL RESPOND . THANKS.
1 Answer Hello Shantilal, the cooktop burner valve ignitor switches are causing the problem , they are part WB24K14. Read More...
V.A. December 14, 2018 for Model Number JGP636BEV3BB I have two issues. One of my burners gives a spark but doesn't produce a flame. What might be the problem? Do I need to replace the gas valve? I have already had someone replace ignition switches to all the burners. There is another burner that is not producing a spark at all.
1 Answer Hello V.A., You should use a safety pin or small paper clip to clear the orifice on the burner that will not light. If this does not correct the issue, you may have a bad gas valve. The one that has no spark at all will need either the ignitor WB13K18 or ignitor wire [WB18K5465] replaced. I'm sorry but this part WB18K5465 has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Thank you for your patience and understanding in this matter. Read More...
1 Answer Hello Winifred. The model number will have to be verified on the units I.D. tag since the one listed came up invalid. This will be necessary to look up and specific parts such as the one you requested. Thank you for your patience and understanding in this matter. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Donna C. December 19, 2016 for Model Number JGP336BEV2BB I am replacing my electrode and the connector is charred. I want to replace the connector but can't seem to find one that is similar. Any advice on what type of connector I should use to connect the new Electrode to the existing wire?
1 Answer Donna, This set of wire terminals WD1X1434D should work to replace the damaged terminal. Just remember the ignitor circuit is a high voltage DC voltage circuit. Make sure when you crimp the terminal onto the existing wire, the connection is proper, good and tight. Read More...
Joseph V October 26, 2016 for Model Number JGP336BEV2BB After I turned the burner off it keeps clicking like it wants to light and you see the igniter trying to light but since the gas isnt on it does light. Is that the igniter.
1 Answer Joseph, This issue would be caused by a faulty ignition switch. You will want to do a continuity test on each of the switches in the off position to determine which switch is defective. If there is continuity in the off position then that is the defective part. The part number for the switch will be WB24T10071. Read More...
Sjd June 01, 2016 for Model Number Jpg930sed1ss The terminal connection for the spark electrode wb13k18 is not making a spark. It has significant discoloration. I want to replace the wire. The wires are not listed in the parts manual and not in the model pictures. Where can I get a wire harness?
1 Answer Hello SJD. Sorry, they do not offer the harness for the igniters on this model. Read More...
Erin June 29, 2015 for Model Number JGP336WEV4WW I have a 15 year old GE gas cooktop model #JGP336WEV4WW. The front 2 burners work click/spark. They only ignite with a match or BBQ type lighter. I replaced the Spark module part #WB13K25. However, the front 2 burners are still not working! What could be the issue? Do I need to replace the Burner Electrodes, part # WB13K18?
1 Answer Hello Erin. You need to check and see if the spark switches WB24T10071 are good on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...