Tom January 08, 2021 for Model Number WSM2700DAWWW All systems working, but loud thumping during both wash and spin cycles. The faster it spins the faster and louder the thumping. I think heavy uneven load may have damaged belt. Any other suggestions.??? Serial AL606116W. 01/06
1 Answer Tom,Remove the front panel and look for something rubbing or hitting with a full load and water. The only other thing I can think of is something stuck between the inner and outer tubs. Read More...
Glenn November 04, 2015 for Model Number NVL333EB4CC I am going to order two glides ,I see felt hanging on the side . Where does that go. Thank you Glenn
1 Answer Glenn, The WE03X10007 front glides ride on the upper WE09X10013 and lower WE09X10013 drum seal. "The dryer drum has two ring bearings made of Celcon M90, mounted 180 degrees apart around the inside of the drum. The bearings snap into holes aroundthe front drum opening are supported by a felt seal attached to the dryer panel, inner door opening, rim flange." Unless the drum bearings were damaged, or they get damaged doing the repair they aren't always needed. But check them closely. Read More...
B.J. January 13, 2014 for Model Number Dryer GE DPXH46EA3WW How many of these parts are on this model? Drum Glide Parts Diagram #1124 / It is listed twice, so does it take 2 to make the Circle?
1 Answer Hello B.J., There are two WE03X10007 required to go all the way around the front of the drum. Read More...
Lance June 20, 2013 for Model Number WSM2700HBWWW When washer gets to the "spin" cycle, it just stops working and it stays filled up with water. Everything else is washing/working ok. What could be the problem?
1 Answer Hello Lance. Make sure the pump is good on the unit and the lid switch is good on the unit. Either will cause the issue you are having with the unit. Read More...
Lmead June 20, 2013 for Model Number WSM2700HBWWW Hi. When I turn on the dryer, it will heat up but the drum does not spin. I checked the belt and it is fine, also I checked all around it but didn't see anything obvious wrong. This is on a GE stackable washer/dryer, model# WSM2700HBWWW. its appx 4 yrs old. Thank you.
1 Answer Hello Lmead. You will need to test for power to the motor. If there is power there, and the heat work, but the motor does not run, you will need to replace the motor in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Cheryl June 18, 2013 Is it hard to replace the Glide-drum (WE03X10007) on my GE Gas dryer? I just ordered this part. What are the directions to replace it?
1 Answer Hello Cheryl. No, just disconnect the power and remove the front panel. Access the inside lip of the dryer drum. Unsnap the old one out of the drum and snap the new one into place on the drum. Read More...
Walsh April 26, 2013 for Model Number wsm2700aww Dryer is squealing constantly and gets louder as it goes on. what are the part numbers for the bearings on the front?
1 Answer Walsh, The bearings on the front would be the drum glide WE03X10007 and there is also felt that goes on the front which are part numbers WE09X10014 lower and WE09X10013 upper. Read More...
K January 08, 2013 for Model Number DSXH47EGOWW I have a GE dryer model# DSXH47EGOW which is squealing quite a bit. What could be causing this and what items should be replaced to stop it? It already has a new coil.
1 Answer Hello K. You need to replace the rear bearing kit WE25X10001 and the front felt seal WE09X10016. Read More...
Kelly August 06, 2012 for Model Number DSXH47EGOWW My clothes are getting all cut in dryer. There seems to be a gap with ruff edges between the drum and the front panel of of the dryer and we can't feel any felt lining around the drum to protect the clothes from getting caught. Is there anyway to repair this??
1 Answer Hello Kelly. You need to order a new bearing kit WE25X10001 and a new upper felt seal WE09X10016 for the unit. Read More...
Ivette July 21, 2012 for Model Number dsxh43ga4ww My dryer drum seal and drum glide that hold the drum in place is what I need. I am not sure of the part numbers. Please help!
1 Answer Hello Ivette, The front drum glides are part number WE03X10007 and two are necessary as they do come individually wrapped. The front upper felt comes with adhesive and is part number WE09X10013. Be sure to let the adhesive dry for at least an hour before operating the machine. Read More...