Liz F February 02, 2014 for Model Number GE Profile Microwave JVM1790SK I can't find instructions on how to replace the interior light in my GE Microwave (Model #JVM1790SK). I am told that I need part # WB08X10057. Is this a simple process or do I need a pro? Thanks.
1 Answer Hello Liz. You will need to remove the outer cover off the microwave to access and replace the bulb in the unit. Read More...
Scott October 03, 2013 for Model Number JVM1790SK01 Can you tell me the part number for a control board for this microwave and is it difficult to replace myself or do I need a technician to do it? Or should I just buy another microwave?
1 Answer Hello Scott! The control board is part number WB27X10866. No, these are not hard to repair. You shouldn't need a technician. Unplug the unit and remove the two screws in the top of the microwave securing the grill. Remove the grill and open the door and remove the screw securing the control panel in place. Pull out the control panel and remove the control board from the panel. Reinstall the new control board in reverse order. Make sure the wires are installed on the new control board the way they come off the old one. Thanks! Read More...
Scott October 03, 2013 for Model Number JVM1790SK01 GE convection microwave about 5 years old. The halogen bulb that illuminates the cooktop surface under the microwave burned out. We bought a 120v 50W replacement bulb. When we inserted the new bulb, it stays on and won't turn off. Is the bulb wrong or is it a bad circuit board inside?
1 Answer Scott, The control board would be the cause of the light staying on all the time. Read More...
Bob C January 09, 2013 for Model Number GSC309PVs02 This is a Whirlpool Micro/Convection Oven and the light has gone out. Can you tell me where bullb is, and how I change it. I've got no pictures or diagrams to go by. Can you help this old man?? Thanks, Bob
1 Answer Hello Bob, The part number that you would need is WPW10440740 and to remove you would have to take unit out from wall. It would be located on top of unit, there is a cover you would have to remove and then remove the spring clip holding it in place. Read More...
Gerri J. December 11, 2012 for Model Number GH6177XPQ-0 My light bulb for model GH6177XPQ0 went out on the left side of my whirlpool microwave. Which halogen light should I order? Can you please help me? Thanks, Gerri
Stephen October 12, 2012 for Model Number GE JVM 1790SK Recently, the halogen bulb (under the unit) that lights up the stove top burned out. The manual calls for a 40 watt max bulb part number WB08X10057. I purchased a replacement bulb and it is rated 50 Watts / 130 volts. I cut the power to the microwave/convection for the installation of the bulb and then reconnected the power. Upon installation of the bulb, the on off switch for that bulb will not work. The high, low option will not work either. Should a 40 watt bulb be used in lieu of the 50 Watt?
1 Answer Stephen, Yes, you need to replace the existing part, with the reccomended part. The excess wattage of the bulb, will cause an increase in heat in the light assembly, and cause premayute failure. You also need to check the holder assembly/wire harness to make sure the connection is proper, and you may want to use a multimeter and check for 120 VAC at the light bulb holder( as long as the microwave is plugged in there's voltage to the bulb, the "N" part of the circuit is completed through the control board) The WB02X35488 and WB06X10554 are the parts you may want to consider, and checking for the voltage at the bulb holder, will get you going in the right direction. Read More...
Osc September 12, 2012 for Model Number WB08X10057 I wish to replace a light bulb from my microwave model JVM1860SF001. Is this the bulb for this model? The microwave has 2 bulbs. From the control pad the bulbs have a low and high brightness setting. Does this replacment bulb also have the low/high brightness ability to function fully?
1 Answer Hello OSC! The halogen lamp WB02X35488 is a microwave bulb, this bulb shines down on the cooktop area. To verify if this is the correct bulb used on your product we will need your appliance model number. Thank you. Read More...
Ladyjane December 26, 2011 for Model Number JVM1790WK My microwave/convection oven needs to have the internal lightbulb replaced. What part do I need and where is in located, is there a diagram showing this? Thank you
1 Answer Hello Ladyjane. WB25X10019 is the correct bulb number. It is located in the top of the cabinet assembly. You will need to un-install the microwave and remove the outer cover to access and replace the bulb. Here is a link to the parts diagram page. The bulb is number 283 in the diagram and will give you an idea of the location. Hope this helps. http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5213553&diagram_id=26637229 Read More...
K November 02, 2011 for Model Number WB08X100051 This is a GE part for a microwave (bulb installs on underneath side of the micro that lights up stove area). It is a 120 volt 40 watt (max) halogen bulb that has three settings (high, low, off). Have they stopped making this bulb and replaced it with the part ending in "057" that is 50 watt and only two settings (on, off)? I use this light in both the high and low settings and really hope it's still available...
1 Answer Hi K. The 50 watt halogen bulb is the one for your unit. Bulb part # is WB02X35488. The control board give the correct voltage through a relay circuit to change it from hi, med and low. Board part # is WB27X10866. Thank You. Read More...
Michael October 03, 2011 for Model Number JVM1790SK01 If I purchase part ap439133 50watts halogen blub, can you give me a diagram where it goes?
1 Answer Hello Michael. The bulb WB02X35488 goes under the microwave and lites the top of the stove. Here is a link to the parts diagram page to help you locate it. It is number 282 in the diagram. Hope this helps. http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5219266&diagram_id=26637426 Read More...