Jeb April 06, 2014 for Model Number kenmore 911.9348810 I'm looking for an infinite switch for kenmore electric range Mod: 911.9348810 Serial# 9D79684. Color: antique or Beige When I enter this Mod# all the parts appear to be for gas but the part I get when I google this Mod# looks correct is it compatible. If so I will order it. Thanks.
1 Answer Hello Jeb! According to the model number given the replacement infinite control switch is part number WB21X36771. Thanks! Read More...
Micky December 30, 2013 for Model Number GE JBP66E0K4BB Is there a way to tell if I have a failed switch or burner. When the switch is turned on the "hot cooktop" comes on but the burner does not. Is there a way to test the burner to verify it is bad?
1 Answer Micky, You can check the burner for burn marks on the coils or test the resistance of the burner element on the 2 terminals on the side of the element. Read More...
Debbie August 30, 2013 for Model Number JBP78BOB2BB START TIME DISPLAY ON FRONT PANEL OF MY STOVE KEEPS BEEPING. IT STARTS BEEPING SLOW THEN SPEEDS UP BUT NEVER QUITS.
1 Answer Debbie, It sounds like there may be a stuck key on the control board which would need to be replaced. part number WB50T10043 Read More...
Brent April 30, 2013 for Model Number JBP68SOH2SS Wondering if you can help me with this problem.The up & down button on control pad became very,very hard to use for about the past 4-5 months. Finally it quit working all together and gave us a code of F7 12 on the read out.The Burners still work fine. I am wondering if I could just replace the "up & down" switch or if I need a whole new Replacement Panel or ERC? I am trying to handle it without getting to in depth. If so , I can get a GE Repairman out to fix it. Thanks in advance...4/30/2013 @ 3:45 pm
1 Answer Hello Brent. No, you will need to order and replace the control board WB27X45466 on the unit. Read More...
Tim March 05, 2013 for Model Number JBP66SH2SS Hi The oven element and the broiler element will not get hot. Within a few miunutes of attempting to heat the oven or use the broiler, the display flashes F3. None of the elements gets hot. I removed the rear panel and disconnected the connector to the sensor to test it with a digital ohm meter with it still bolted to the oven (sensor bolts were very rusty). It measured 59.kiloohms. I assume that the sensor is bad. Willa bad oven sensor prevent the controller from turn on the oven and broiler element? The top elements work fine.
1 Answer Hello Tim. Based on the error code you provided, the oven sensor WB21X22134 is bad and will need to be replaced on the unit. Read More...
George January 12, 2013 for Model Number jbp71wof2ww Left front burner turned on by itself and the hot light stays on.
1 Answer Hello George, This would be a bad infinite switch and will need to be replaced. Read More...
David November 03, 2012 for Model Number JBS27WHZWW Which control switch I need to order for 6" Surface Unit ASM. WB24T10025 or WB24T10029? The owner manual shows both. I don't know what is the difference and please advise. Thanks, David
1 Answer Hi David, the switches are different depending on if they are for the large element or the small element. The switch for the 8" element is WB24T10025. The 6" element switch is WB24T10029. Thanks! Read More...
Sonny August 31, 2012 for Model Number jbp24bh3wh Infinite switch can't maintain temp on my 8" electric burner. After checking your parts list....which one should i order, INFINITE CONTROL SWITCH 1500W (4076) or the other SWITCH (4072). I ordered the PN wb24t0025, installed it and it blew-up and tripped the breaker. Help !
1 Answer Hello Sonny. You need to order part number WB24T10025. If it blew up, you had it wired wrong. Make sure the switch is wired correctly. L1 goes to L1 and H1 to H1 ect....... Read More...
Ron July 19, 2012 for Model Number jbp21wh1ww One of the 8 in element gets hot too fast, by turning the control knob only slightly to 1, the element gets super hot within seconds. Switched the front to back and it still does it. What do you think?
1 Answer Hello Ron. Based on the information you provided, it sounds like the infinite switch WB24T10029 is bad and needs to be replaced. Read More...
Mike January 30, 2012 for Model Number JP64BOB5WH My oven is not working. Indicator light keep flashing no heat.
1 Answer Hello Mike. See if there is power coming from the EOC to the bake element when in bake mode. If not, you will need to replace the EOC WB27T10231. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...