Don March 26, 2026 for Model Number PSS26MSTE SS Ice maker works fine. new filter and filter manifold. Display panel Wr55x10631 first button switch LED blinks continuously. The panel does not trigger ice dispensing or water fill. Essentially, the panel is dead, other than the blinking light. No water fill, no ice dispenser, but the ice maker itself sure makes ice. We just pull ice out manually. What would make the panel only have one blinking light, and otherwise be inoperable? While the internal ice maker works fine?
1 Answer Don, Try to unplug the unit for 5 minutes to reset it. If this does not correct the issue then this would most likely be a faulty display board. Read More...
Doug November 18, 2016 for Model Number AP3965182 I was replacing my ice despenser silonoid when I put it all back together now the dispenser control panel doesn't do anything. None of the lights are on the panel and I have checked. The panel is getting power. Bad panel? It was working fine till I changed the silonoid. Thanks Doug
1 Answer Hello Doug. Make sure everything is plugged in good. If so, then you will need to replace the panel. Read More...
Mark December 16, 2014 for Model Number PSS26MSTASS Water dispenses just fine. Ice will not dispense and makes no noise. Just replaced the dispense board. What else could it be?
1 Answer Hello Mark. Test for power at the auger motor. If there is power there, and the motor does not run, you will need to order and replace the motor on the unit. Also, make sure the dispenser switch is good. If the switch is good, and the motor has no power, then the main board will need to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
John October 07, 2013 for Model Number ge profile pss26mstdss My problem is the ice and water dispenser, when I chose either water or ice nothing comes out. and then the light on the display goes out then comes on when I remove the cup. I don't know if its the circuit board on the freezer door or the main board behind the fridge. please help.
1 Answer Hello John. It sounds like the main board in the back of the unit is bad and will need to be replaced on the unit. Read More...
John September 01, 2013 for Model Number PSI23NSTC SV Ice dispenser auger does not rotate. Using voltmeter, found that there is no power to auger motor (remains at 0 Volts when dispenser pressed and light switch closed - what voltage should be at auger motor if working properly?). Tried replacing Interface Disp Asm (AP3965182), but did not resolve problem. Water dispenser on freezer door works fine, however. What do you suggest? Thanks for your kind help. Best regards, John
1 Answer John, On the main control board, test connector J7 pins 1 to pin 9 and push the dispenser lever on ice. If there is not 120 vac then the main control board is faulty and would need to be replaced. Read More...
Carmen September 22, 2012 for Model Number PSS26MSTD The control panel to either select water/crushed/cubes/quick ice has worn out on my unit. The replacement part is GE Interface Disp Asm (Part Number: AP3965182). How do I get the old one off the freezer door??
1 Answer Hello Carmen. The interface WR55X10631 unsnaps from the freezer door. You can use a flat blade to pry it from the bottom right side corner. Read More...
Bill M August 13, 2012 for Model Number GE: GSS25LSWA Refrig. Hi John: Water & ice are not dispensed. When the paddle is pushed in, the selection lite goes out, then the ‘0' freezer temp & water [or ice] lites repeatedly blink on, then off.
1 Answer Hello Bill. If the lights go out when the dispenser is pressed, you will need to order and replace the main control board WR55X10942C on the unit. Read More...
John C. February 03, 2012 for Model Number pss26mstdss The ice and water on the freezer door is not working. The cube light is on and nothing else will work. I replaced the mother board and the control panel on the door and still not working. Can you help ?
2 Answers John, Did you also check the actuator switches in the dispenser ? if one is shorted and has the incorrect circuitry, this will " lock up" the control board. You would also want to check the J7 connector harness on the "mother board" for a good and proper fit on the pins of the board. Good Luck and Thanks Read More...
John C. February 03, 2012 for Model Number pss26mstdss The ice and water on the freezer door is not working. The cube light is on and nothing else will work. I replaced the mother board and the control panel on the door and still not working. Can you help ?
2 Answers Hi John. Remove the power. Look under the upper fzr.door hinge at the molex electrical connectors. See if the pins have separated by unplugging them. Use a flashlight if needed. The pins individually are pushed in from the back of the connector plug. They are slightly common to not lock into place fully therefore backing out and not connecting fully. They will electrically arc and burn open enough for a break in voltage feed. If so, then either repair the pins or jumper them with a wire and bypass the connector altogether. As long as the new repair fits clearly under the hinge cover smoothly without getting pinched. If these are Ok, then look at the freezer door switch part # WR23X31507. The power starts and stops there when the door is opened .Please let me know what you find so I can assist. further. Thank You. Read More...
Tom H September 10, 2011 for Model Number PSS26MSTD SS Chute for icemaker got clogged with ice cubes. Cleared chute of cubes & worked OK. Poured a couple of glasses of warm water down door chute to melt away remaining ice on edges. Next morning auger & crusher won't work. Can turn auger motor by hand. Water dispenses fine. On cubes or crushed setting, panel light temporarily dims & fan temporarily shuts off, but no auger or crusher action. Light & fan resumes after a few seconds. Would a damp interface assembly do this. If so, can I dry it out with a hairdryer?
1 Answer Tom, You may want to try drying the board and wiring out with a hairdryer, it may solve the issue, but based on your information< you may have damaged the dispenser board, beyond repair, and will need to replace it. Good Luck and Thanks Read More...