Jeff March 20, 2012 for Model Number hss25gfpjww My ice maker is working. I can select Water/Cube/Crush. The lights work. Nothing dispenses when the push lever is engaged on the outside freezer door. The light seems to dim a bit when engaged.
1 Answer Hello Jeff. You either have a bad dispense board WR55X10446, (most likely), or a bad main board WR55X10942C, (which contains the power supply for the dispense board). I hope this aides in your repair. Have a great day! Read More...
Paul March 15, 2012 for Model Number ge model : ZISW420DRI My GE refrigerator water flow out of the water dispenser by itself, only I can stop it have to take off water filter? Any idea what is wrong? Here is the model number: ZISW420DRI
1 Answer Hello Paul. Check and see if the switch WR23X10783 is bad and if not, it sounds like the water valve WR57X33326 is bad and will need to be replaced in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Monkee February 22, 2012 for Model Number GSS25SGMBBS My dispenser works, but the ice chute flap doen't open. What part is needed to make this work again and im getting alot of frost build up in the interior of the chute oping for the ice exit????
1 Answer Hello Monkee. Based on the information you provided, it sounds like you will need to replace the solenoid WR62X10055 in the dispenser. Hope this helps. Read More...
Michelle Elrod February 02, 2012 for Model Number GSS25JFPD CC My water dispenser & no solid cube ice but I am getting crushed ice. What could be the problem?
1 Answer Hello Michelle. Check and see if there is power going to the solenoid assembly WR62X23154. If so, and the solenoid is not changing, you will need to replace the solenoid. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
John December 20, 2011 for Model Number GSH25KGMDWW The control panel that has the selection for ice (cubed or crushed), water and light does not show to have power. The water filter reset and the lock/unlock reset do not work either. Its like it has no power.
1 Answer Hello John. If there is no power to the dispenser board, you will need to replace the main control board WR55X10942C in the unit. Hope this helps. Read More...
Travis December 15, 2011 for Model Number GSL25JFTABS No water out of dispenser. However when I disconnect the coupler at the bottom of the door and push the switch water does flow. I tried to use my air comp to clear the line but nothing is coming out. Any ideas? I also can't figure out how to remove the line and see whats blocking it.
1 Answer Hello Travis. Based on the information you provided, the water line is frozen. You will need to use a hair dryer or unplug the unit with the doors open for 5 to 7 hours to thaw out the water line. Hope this helps. Read More...
Jr A. November 17, 2011 The ice maker is making ice. I can select water, cubed or crushed on the dispenser but it won't dispense anything?
1 Answer Hi Jr. We are going to need the model # to assist you further with the correct part #'s. Thank you. Read More...
Steve October 30, 2011 for Model Number GSS25WATASS I am not getting water flow out of the water dispenser in the door. I have removed the filter and it was pressurized. I then went to the back and I get water from the valve. I then disconnected the from and get water from valve to the front of the frig. What else is there to check?
1 Answer Hello Steve. Based on the information you provided, the water line in the freezer door is frozen, and will need to be thawed out. You can use a hair dryer to do this, but be careful and don't melt the door liner. Hope this helps. Read More...
Ken P. October 14, 2011 for Model Number GSS22IFPA WW We are having trouble with the funnel ice dispenser. It is loose and floppy and we think also the switch could be bad. We are not getting water but we were getting ice. Now we are not getting either. I need to know how to take off the front to get to these parts.
1 Answer Hi Ken. The Ice dispenser solenoid is part # WR62X10055. Ice door assy. is part # WR17X11653. Switch is part # WR23X10783. If you need further assistance let us know. Check your e-mail for the instructions. Thank You. Read More...
1 Answer Hello Mauricio. We will need your model number to help you with this. Thanks. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...