Steve October 28, 2017 for Model Number JB500G0J1WH I need a replacement burner part# WB30X346 but there is no available part, Is there a replacement that would work for this? Thanks
1 Answer Steve, Unfortunately the surface element WB30X346 has been discontinued and there is no suitable replacement available. Read More...
Larry S October 06, 2017 for Model Number JB500D2HA What burner coil will work as a replacement for Part Number: AP2027828 MFG Part Number: WB30X346? Thanks!!
1 Answer Larry, The surface element that is showing for your model range will be WB30X219. Unfortunately the element WB30X346 if it is needed would be discontinued with no suitable replacement available. Read More...
Ed M January 07, 2017 for Model Number JB550G0J3 The triple burner (AP2027828 or WB30X346) has burned out. In looking through your site this part is not available. What are my options?
1 Answer Hello Ed. Sorry, this part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Jim June 06, 2016 for Model Number jb500gob1a GE range I was using your chat & Cierra found the part number to replace our three temperture 8" burner, #AP2027828. But when I use the compatibility checker, it says not compatible. Please advise - also,can you explain the removal & install? Thank you, Jim
1 Answer Jim, In order to change this part you would simply unplug the unit and then lift the element out of the unit. It will be held in with screws attached to the wires and you just disconnect the wires. The compatibility tool does not work unless you put the model number in perfect the way that our system would have it listed. For your case that would be JB500G*B1 because this is how GE lists it. Read More...
Larry S March 26, 2015 I have a GE electric range top with a 6-8 burner element that needs replacing. I found a 4-6-8 unit (AP2027828) but no 6-8 unit. Can you help with that?
1 Answer Larry, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Jason H February 21, 2014 for Model Number JB600G001A I removed the burner on the right front of my stove for cleaning. I did not label the wires when I took them loose because I was going to put it right back together. Well I had a family emergency left everything and went to ER. few hours later came back and for got where the wires go. There is 4 wires because it is a power saver 4,6, and 8 on that burner can you please help me with this? Thank You very much!
1 Answer Hello Jason. The model number you provided is not working. You need to check and see if the model number is correct. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Keenpa August 29, 2013 for Model Number JP310- ON2WH (GE) We have a countertop with a set of 4 burners. The "4-6-8" burner is not working, but the landlord supplied a WB30x346 as replacement. I've previously confirmed that this will work. The issue is that the existing connecting wires are Orange, Yellow, Blue, and Green for the connectors on the stovetop unit. I am not sure which wire gets attached to which of the 4 connectors on the burner unit. There is no wiring diagram included.
1 Answer Keenpa, Unfortunately we do not have a wiring diagram for the unit. Here are the steps that you will want to take. While connecting wires make sure that the power is off. You will need to access the switch for the element. Follow the H2 terminal wire which will be the L2 circuit and will go to the terminal that is off by itself on the element. With the power on you will need to set the switch to low and test from each wire to ground and the wire that you get 120 volts from will go to the innermost terminal on the element. Then put switch on medium or the 6" and test the other 2 wires. The one that has 120 vac to ground will be the center terminal connector. The other wire will be the outer most terminal. Read More...
Jay A. August 29, 2012 for Model Number R B747G 0J7AD I have a Hotpoint electric stove. Will this part replace the oven burner that I have that is no longer working (8 inches)? Thank you.
1 Answer Jay, according to your model number the replacement 8" element is part number WB30M2. Thanks! Read More...