Jmo June 13, 2020 for Model Number LSXS26326S/00 My ice maker makes ice, but the cubes stick to the tray, so the tines on the part that scoops them out gets stuck till I water the cubes down to unstick them. Is there a replacement for the tray?
1 Answer J Mo, There is not a replacement for the tray and you would need to replace the complete icemaker for this issue. Read More...
1 Answer Aaron, it would be recommended that the freezer temperature is verified as being less than 10°F using a thermometer. If it is, the next step would be to inspect the fill tube for an ice blockage. If there is ice blockage in the ice maker fill tube, it would need to be cleared and the valve replaced. If not, the next step would be to use a small tool (like a small safety pin) to press the test button located on the right side of the ice maker motor (if there is not a reset button). This should cause the ice maker to go into a harvest mode. If the ice maker goes through a full harvest, the ice maker has failed and would need to be replaced as it would not be sensing the ice tray properly. For the most accurate information regarding part numbers, the model and series numbers would be necessary. In regards to the ice maker part number, the most accurate part number would be located on the back of the original ice maker. Read More...
Jesse May 11, 2020 for Model Number LSXS26366S/02 I notice that the auger that dumps the ice is facing up in the 12 o'clock position. Would that be the cause for it not making ice? And I noticed when I looked in there, there was ice build-up where the water comes out to fill the ice tray
1 Answer Jesse, Based on this description it sounds likely that the icemaker mold has filled with too much water causing the arm to not be able to turn. The fill cup also being full of ice indicates this. The water valve not closing all the way would be the most likely cause of this issue. Read More...
Gregory Davis December 28, 2019 for Model Number AEQ73130002 Ice forms at fill nozzle shutting off water disableing the ice maker. This requires getting out the hair dryer to melt the ice. Than I am good for a few days. Then do it again. Do I have to replace the entire unit?
1 Answer Gregory, This issue would be caused by a water inlet valve that is faulty and would need to be replaced. Read More...
Cecil September 13, 2019 for Model Number LG LSXS26386S /00 I can see how to easily remove the ice Maker from the door. However, the wires run from the ice maker into the door panel. Is the plug for the wires behind the door panel? What is required to remove that panel to access the electrical plug?
1 Answer Hello Cecil, You will have to remove the auger motor cover EAU61004410 to disconnect the harness since it plugs into the door liner behind this panel. Read More...
Stanley September 02, 2019 my icemaker has ice in it but it is not dumping the ice, not sure what is wrong
1 Answer Stanley, We will need your model number to help you find the right parts for your unit. Please post another question with all your info included thank you. Read More...
Jim December 03, 2018 for Model Number LG AEQ73130002 Hello. I have a LG AEQ73130002 model ice maker that I need two gears and a small spring for. Can you send me a diagram or tell me where I can get a diagram that shows the inner gears and works with part number so I can order the right parts
1 Answer Jim, The manufacturer doesn't list internal parts. They only offer complete replacement of part AEQ73130002 Read More...
Ron July 09, 2017 for Model Number LSXS26326S Appears that to replace all I have to do is unplug the wiring harness for old one and then plug in new, attach ground wire, and reinstall. However, there appears to be other wires "plugged" into the back of the door.and I don't want to mess anything up. Is it any more difficult than that?
1 Answer Ron, The way that you described it will be the way to replace the icemaker on this unit. Read More...
Kent March 23, 2017 for Model Number LG-lsc22991st/01 How difficult is it to change and hook up a new ice maker on this model of LG refrig? Not sure where to hook up the wire harness and the water tube.
1 Answer Kent, When you open the left door that houses the icemaker and the door covering the icemaker there will be 4 to 6 screws that hold the complete assembly in place. Remove the screws in that compartment and remove the holder and icemaker in order to disconnect the icemaker. Then remove the screws for the icemaker and remove icemaker and install in reverse. Read More...