Ron December 29, 2020 for Model Number WM2277HW The dispensing tray wouldn't open and so it broke off a piece of plastic from the back that resulted from too much force applied during extraction. This is called a drawer panel assembly with part # sequence: AP4439235 and a Mfg's part # sequence: 3721ER1073D. The statement is made that this detergent drawer that slides in and out of the LG high capacity front loading washing machine has in fact become a discontinued part. While using the tray now once the wash has been completed the tray fills up with water which is obviously a hazard if left inside the unit as mold could start to form. Please confirm that if the exact part is not available that one which is similar and can still work in our existing model can be used as a substitute and perform the same function without any leaks, gaps or any other glitch in the matrix? Thank You.
1 Answer Ron, unfortunately, as the manufacturer has discontinued the drawer panel assembly 3721ER1073D and has not listed an approved substitute, we would not be able to guarantee an alternative would fit properly. Read More...
Terry October 11, 2018 for Model Number WM2277* Drawer Panel Assembly - The small soft rubber bullet-nosed shaped grommets where do they go OR where did they come from. Found in the drawer about the size of a number 10 screw head
1 Answer Terry,That sounds like it could be plugs used by the manufacturer in the back of the dispenser for holes they don't use on certain models. You can remove the top panel and check the rear of dispenser housing or possibly remove the trays in your dispenser and check underneath them to see if they are used there. Read More...
Yvonne April 20, 2018 for Model Number WM2077CW I need to replace the soap dispenser drawer. What is the part number I need?
Mike February 08, 2018 for Model Number wm2277hw I replaced the soap dispenser draw with a new one from your company, but the draw hangs up approximately 1 inch before it is completely closed. Have to pull real hard to get open and push hard to get it to close. Is there a quick fix or is it possible the draw is the wrong size?
1 Answer Hello Mike. Based on the model number you provided, 3721ER1073D is the correct drawer. You will need to check the dispenser and see if it may be bad on the unit. Thank you. Read More...
Donna B. January 09, 2016 for Model Number WFW9400SW02 The drawer panel after each wash is full of water where you put the bleach. The softener side doesn't work either. The only one that works is where you put the detergent. Do I need the draw panel assembly? If so can you give me the correct part number? Thanks
1 Answer Hello Donna, This is normally a bad actuator WPW10352973 on the detergent dispenser. Read More...
Don A. January 10, 2015 for Model Number WM2277HW The detergent dispensing drawer is "stuck" and can't be opened. How can I access the drawer to remove it and what is the most likely cause of not being able to open it?
1 Answer Don, Most likely one of the siphon caps on the drawer is not in position properly. There is one of 2 ways to get this open. The first would be to try to take the top off the unit and try to take the top of the dispenser housing off. There are clips on each side to get this off. If this is unable to be done then you will need to pry the drawer out and most likely will need to replace the drawer and the housing because it will most likely get damaged. Read More...
Al January 07, 2015 for Model Number WM2277HW The dispenser Trays are left with a full amount of water after every wash. Dispenser Trays have been cleaned thoroughly but water is still left in them after each wash. What can I do to solve this problem? Thanks; Al
1 Answer Al, You will want to pull the drawer out and make sure that the holes in the top of the housing are not clogged as this would most likely be the cause for the issue. Read More...
Tammy October 21, 2014 for Model Number WM2077CW I need to replace my drawer, the assembly drawer that holds and distributes the detergent, softener and the bleach. I see in the picture of the drawer the lid caps are on. My question is, are they included with the drawer or have to be purchased separately? Thank you.
1 Answer Hello Tammy! The caps, handle, and drawer are all included in the drawer panel assembly 3721ER1073D. The detergent box part number 3891ER2003A does not come in the assembly. Thanks. Read More...
Carol September 25, 2014 for Model Number WM1812CW I need a dispenser drawer for this model machine. The part number is 487OER1010 for the drawer. The model looks the same but the numbers don't match. Is this the proper drawer?
Mark K July 08, 2014 for Model Number WM2277H WE have an LG front load washer. The dispenser assembly drawer will not come out/or pull out. the 2 tabs are up on detergent and fabric softener. How can we get this open to replace it.we took the drawer panel off and still cant get it out. Please help us I cant afford a repair man at present time. We Thank You
1 Answer Hello Mark. Try wiggling the drawer up and down and pulling at the same time to break it loose. Read More...