Gerardo June 04, 2022 for Model Number RF28HDEDTSR/AA-01 Does the Samsung DA61-05435A freezer arm replacement part come with the screw needed to install? If not, what screw is required?
Robert September 29, 2020 for Model Number rf323tedbs My bottom ice maker stopped working about a month ago. I decided to try and fix it. I can do a reset and the tray dumps water the sensor full goes down and than goes back up and stays there. So I have tried to find a fix online and nothing. Have you seen this before and what is the fix. Model # rf323tedbs
1 Answer Robert, based on the information provided, it would be recommended that the freezer temperature is verified as being below 10°F with a thermometer. If the freezer is at the correct temperature as shown on the temperature display, then the failure would likely be in the ice maker DA97-07603B as it will go through a forced harvest. Read More...
Steve July 03, 2020 for Model Number RF28HFEDTSR/AA Need icemaker shut off arm AP 4446159 (DA61-05435A). Website indicates out of stock. Q&A projected no longer avaialble? So what gives: is it out of stock or no longer avaialble?
1 Answer Steve, This part is no longer available by itself. The ice maker would need to be replaced. Read More...
Tim May 30, 2020 for Model Number RF28HFEDTSR/AA Where is the water valve located on this ref? I can't seem to find it in the diagrams, part # will be good also.
1 Answer Tim, the water valve is going to be a part of the water filter housing assembly DA81-05998A. Read More...
John April 14, 2020 for Model Number Da6105435 No need to replace the arm I repaired mine , super glue the arm back together and then fill both sides of arm with epoxy one side at a time this will never break again.
1 Answer Hello John, unfortunately, the arm (DA61-05435A) is no longer available as it has been discontinued by the manufacturer. Read More...
Karen September 28, 2019 for Model Number RF260BEAESR/AA We need to replace the Guide-Ice-Full part DA61-05435. However, been told by Samsung part is not longer available. Any suggestions for the next best thing/part? Thank you
1 Answer Karen, the next best thing to replace the guide arm would be to replace the entire ice maker DA97-07603B as it is still a manufactured part. Read More...
Jim December 10, 2018 for Model Number RF261BEAESP/AA-0001 How to lower or drop the Icemaker Shut Off Arm #DA61-05435A into ice bin after replacing arm in the up position?
George April 18, 2017 for Model Number RF263AERS Have ordered the ice-full sensor arm for the icemaker. Is there somewhere that gives instructions on installation? Can installation be done without removing icemaker from refrigerator?
1 Answer Hello George. Very easy to replace. Just remove the bucket and remove 1 screw securing the old arm. Then slide new arm into place and reinstall the screw. Read More...
Bud October 26, 2015 How do I remove the icemaker to repair the full arm ? Samsung Mod . RF323TEDBSR. Bottom Icemaker
1 Answer Hello Bud. When pressing the Energy-Saver and the Fridge buttons on the Display together for 8 seconds at the same time, it will convert to the Test Mode and the entire Display function will be off. When pressing any button within 15 seconds after it is shifted to the Test Mode, its function will change in the following order. Manual operation1(FF) Manual operation2(0F-r) ? manual defrost of fresh food compartments(rd) ? manual defrost of fresh and freezer compartments(fd) ? cancel(Display all off). ? Set unit to Fd for 5 minutes. This will allow for easy removal of the ice maker. While pressing the tab on the top right side, lift up the Ice Bucket and pull it out Remove the screw from the Wire Housing Cover. Remove the Wire Housing Cover. Disconnect the Ice Maker Housing Connector. Remove the screw from the Duct Tray-ice. With a flat blade screwdriver, push the duct to the right and remove it from the locking tab. With a flat blade screwdriver, pry down on the refrigerant tube to separate it from the bottom of the ice maker. Push down the refrigerant pipe slightly and separate the refrigerant pipe and the Ice Maker Assembly completely. While pressing the Hook, pull out the Ice Maker. While pushing down the Duct-Tray-Ice, pull out the Ice Maker carefully and remove it. ? When removing the ice maker, be careful not to damage the grommets on the tray or the refrigerant tube. Re install in reverse order. Read More...