Richar S October 12, 2022 for Model Number Samsung RS271T5200SR/AA My ice maker stopped dumping ice after it was frozen. When I hit the test switch it will cycle. It fills with water properly and may keep cycling until the ice bin is full. It will not reset after that.
1 Answer Richar S, Thanks for the question. Based on the information provided you will need to check to make sure the temperature at the ice maker is below 8°F. If not then your issue is a cooling issue and if the temperature is below 8°F you will need to replace the ice maker. Read More...
Pip July 22, 2020 for Model Number Samsung side by side RS2530BSH I have Samsung side by side RS2530BSH. I turned off the ice maker after it over-flowed and froze a large block of ice in the freezer. I did a full defrost and have now installed a new icemaker unit, DA97-02203G. the install was easy. The reset button cycles and tips the tray but no water is filling the tray. The water dispenser works correctly and the icemaker selection on the front control panel is turned to cubes. Suggestion on how to get the water flowing to the ice tray?
1 Answer Pip, Make sure that the water line is not frozen and if it is not then it sounds like the water valve would be faulty and would need to be replaced. Read More...
Roger July 13, 2020 I ordered a part back in September of last year. The part I ordered was DA97-02203G. The problem is I received part number DA-97-02203H (which has a stair step mount where the screws go but should have been flat all the way across where it mounts. This is one of those projects you intend to get around to but time just gets away, so my questions are Could I still send the part I received back and exchange it for the right one or do I have to just re-purchase another one and hope the right part comes in? The previous purchase info is: Inv Doc: 5111837 PO Number: 10568322-9275342 Pick Ticket: 4531283-01 Any help I can get would be greatly appreciated.
1 Answer Roger, For this issue, you will want to contact customer service at 877-477-7278 and talk to them about this. Read More...
Juan Medina May 01, 2020 for Model Number Ice maker lifter Do you sell the plastic stopper for the ice maker for Samsung refrigerator model number RS2530BWP?
1 Answer Juan, You would need to replace the icemaker to get the arm of the icemaker. The icemaker for the unit will be part number DA97-02203G. Read More...
Kathy January 14, 2019 for Model Number RB215LASH Installed icemaker part#DA97-02203G and water is leaking out of the back panel of freezer. I have left it off for 24 hours to see if the water accumulating in the bottom under drawer was when the ice maker is on and it is. I need to remove the panel on the back wall of the freezer to find out why it is leaking. The ice dumps fine and water fills up in ice tray but I M getting a build up of ice in the bottom of freezer can you help?
1 Answer Kathy, it sounds like you have a defrost drain clogged up and not able to drain out.DA97-04046A Is the part number in question you would need to access the back panel and remove it and clear the ice covering the drain. A garden sprayer with hot water will allow you to clear the drain where water will flow out. Then pull the unit out and remove the lower rear cover and replace the drain tubes. Read More...
Jeff October 22, 2018 for Model Number samsung refrig rsg257aars with ice maker da97-06364b The ice maker does not fill with water. I have already replaced the valve in the lower back. If I pour water in the tray it works fine. Does the ice maker itself have a valve that lets water in? i don't want to buy a new unit if there is not a valve inside the maker itself. Do I?
1 Answer Jeff, You will want to check the water valve that is in the unit to make sure that there is 120 vac getting to it when the icemaker cycles. If there is not 120 vac then the icemaker would be the issue and if there is 120 vac then the valve would need replaced. Read More...
Jake August 24, 2018 for Model Number RS277ACPN/XAA-0000 my ice maker is not dumping ice out of the tray it just fills and water gets everywhere when i turn it on because there is already icecubes in the tray do i need a new ice maker or control board?
1 Answer Jake, You will need part # DA97-02203G freezer ice maker.We know the control is sending power to unit because of the fill. Read More...
Patrick Barrett August 23, 2017 for Model Number RS2555SL/XAA Ice maker Samsung DA97-02203G started dropping ice too early while the middles are still water. water goes down on cubes and welds them together. ice is formed on the auger. and the whole thing becomes a ice dam. auger can't move. as far as I can see, when it fills the tray after dropping cubes, no leaks or drips. temp set at -14. reads about 4 on digital thermometer. can the heater under the tray be staying on continueously? this is a new ice maker last may
1 Answer Patrick, While it would be possible for the heater to stay on but would more likely be a issue with the thermostat on the icemaker itself where the icemaker owuld need replaced. Also you would want to make sure that the the temp setting is at -2 to see if this will correct the issue. Read More...
Jody August 01, 2017 for Model Number RS275ACBP/XAA Our ice maker is not making ice fast enough. It takes up to 4 days to fill our bucket of ice. Also, our ice is crushed all the time even though we have the setting on cubes. What can I do to fix these 2 issues?
1 Answer Hello Jody, If the cubes are hollow you will need to replace the water valve DA62-00914B. If the cubes are solid you will need to make sure the temperature in the freezer is 0° to 10°F. If so, replace the icemaker DA97-02203G. The cubed ice is dispensed only when the lever on the ice container is actuated so you will need to determine if it is being actuated. If so, an electrical issue has been eliminated and the issue is likely to be the ice dispenser solenoid DA74-40151G. Read More...
Kyle C January 12, 2017 for Model Number RS277ACPN/XAA-0000 I bought the new ice maker from you and installed yesterday. It makes ice but will not automatically dump ice. I have to use the reset button on the new ice maker. It fills with water and cycles thru after testing but will not continue on its own. Any thoughts?
1 Answer Kyle, With the icemaker having to be manually cycled, this would most likely be caused by a faulty main control board that is not reading the sensor properly. Read More...