Monsell N April 29, 2018 for Model Number Burner piece , it looks like aluminum? How do you clean them?
1 Answer Monsell, To clean the burner assembly you would just clean with soap and water. For the orifice you would remove it and make sure that the port is cleaned out. Read More...
Bill Greene February 18, 2018 for Model Number KGCS166GBT2 I need to replace the burner orifices for the two 6K burners (right-front and left-rear). When installed, the appliance was converted to propane with the wrong orifices on those two burners, causing yellow flame . These two burner heads are too small for me to remove the orifices from the top - I'll need to remove the cooktop to access them. But the stovetop is 14 years old, and none of the torx screws can be removed, so I'll have to drill them out of all five burners. After having done that, I think I'll need to replace all of the burner assemblies that the torx screws go into. Does that sound right? In that case, I have 5 burners and I see 4 parts (#15 on the diagram). Can you please tell me which ones I need, and where they go? Thanks, Bill
1 Answer Bill, If you were able to drill out the holes without damaging the orifice holder then you should not have to replace the holder. If the threading was damaged it would need to be replaced. For the orifices in LP you would need to get the LP kit for the unit. Read More...
Kevin October 01, 2017 for Model Number KGST307HBS6 My left front burner will not light and even when using a match to light only holds a very low flame. It won't increase flame size even while adjusting. Does the whole mechanism need to be replaced?
1 Answer Kevin, This issue sounds like it would be caused by a faulty valve assembly as this would be the only thing that would control the flame size. Read More...
Laura August 03, 2017 for Model Number KGCC566 There is a small metal piece resembling a staple lying under the left front burner cap near the igniter. Could this be the reason why just this burner is clicking but not igniting? Did it break off the igniter? All other burners were clicking too but we cleaned and dried all 5 burners and now just the front left burner is not igniting. Thank you.
1 Answer Laura, We are not aware of a clip that would look like a staple on the unit. It is very possible this could be the cause of the igniter sparking but not lighting. If the unit will light with a match then this will likely be the issue. Read More...
Don Maner July 12, 2017 for Model Number Whirlpool Gas Cooktop MDL. GLT3034LQ0 Need left front (large) burner assembly (with igniter). What is correct PN? Should I order screws? PN?
1 Answer Don, To receive the burner base and igniter you will need to order the 814514 / 9754187 Burner assembly. Yes, we would recommend you order the burner base.orifice holder mounting screws WP3368921 / 3368921, just in case, they have been known to strip and break off. All parts are in stock and available at this time. Thanks, Read More...
Ping Z November 16, 2016 for Model Number KGCS166GSS07 My front left burner sometime works and sometimes does not. I found the spark of of this burner is not as big (strong) as the others. Do I need just replace the electrode? What would be the model number?
1 Answer Ping, You will first want to make sure that the burner head is clean and that the burner cap is in place properly. If this checks ok then the electrode would likely be the issue. For the igniter on this unit you will need to get the orifice holder WPW10155786. Read More...
Ryan April 23, 2016 for Model Number SCS3014GS0 I'm looking to replace some burners on my cooktop, when I converted it from NG to LP I broke some of the torx screws off. I just need to replace the Left Rear (9k) and the Left front (11k). Which two parts do I need? Are the outputs posted in the reading for NG only? And also do I need to purchase the Torx screws also?
1 Answer Hello Ryan, You will need to order 814513 left rear, 814514 left front, and as many burner head screws as needed. These will come set up for natural so if you need to convert to LP you will need to order 3192261 if the existing orifices cannot be re-used. Read More...
Bill January 25, 2016 for Model Number KGCS166GWH1 I need the left front burner assembly part number for model number KGCS166GWH1. Just making sure I get the right one. Thanks!
1 Answer Hello Bill. WP4455849 is the left front burner head. WP9754188 is the orifice holder for the unit. Read More...
Brad August 20, 2015 for Model Number SCS3014LQ0 I NEED THE LARGE FRONT LEFT BURNER ASSEMBLY WITH BURNER HEAD. WHICH ASSEMBLY NUMBER IS IT? AND DOES IT COME WITH NEW SCREWS OR NOT
1 Answer Hello Brad. You will need to order 814514 and 2 of WP3368921 for the left front. Read More...
Manny April 01, 2013 for Model Number Whirlpool Countertop Stove - Gas Mod. No. SCS3014LB0 The ignitor will not work on two of the stoves, the front left and right. Also need replacement knobs, are they like $31 for one or a set of 4?
1 Answer Manny, For the igniters on your unit you will need to replace the burner assembly as the igniter is not sold separately. The Right front burner is part 814512 and the Left front is part number 814514. You may want to check the burner switches to make sure that they are good. To test the burner switch you would disconnect power and gas to unit. Turn the valve on for the burner and test to see if there is continuity. If there is continuity then it is ok. For the knobs you would have to order 4 knobs. Read More...