Anna September 24, 2018 for Model Number gfg464lvs1 Whirlpool gfg464lvs1 oven does not work however the broiler and burners work great. The oven clicks 3 times, the gas lights for a few seconds with strong blue flame and then shuts off. I cleaned the burner and tested the tested the thermometer. Now I'm looking to get replacement parts. Do I need the burner/igniter or the spark module?
1 Answer Anna, This issue sounds likely that the oven safety valve is faulty and would need to be replaced. Read More...
John S. January 03, 2016 for Model Number WFG510S0AS0 Bake Function on the oven doesn't always ignite. When I turn the oven on I hear the gas valve open, can hear the igniter spark and sometimes the burner ignites and sometimes it doesn't. I checked the spark module for proper voltages, it tests within the normal ranges (125 VAC and 9.5 VDC) whether the oven turns on or not. This happened about a year ago as well and I replaced the igniter, which didn't resolve the issue. I removed and cleaned the burner and the original igniter and everything worked fine until just a couple days ago and now the same thing is happening. The broiler works everytime, no issues. Spark Module was replaced once under warranty and is just about two years old.
1 Answer John, You will want to pull the oven burner out and try cleaning it again. With this being an intermittent issue, that is going to be the most likely cause. If there is rust around the ports then it would be a good idea to replace the burner. Read More...
Mcola October 14, 2015 for Model Number GFG461LVS0 This gas range is about 4 years old. The problem started a few weeks ago. The broil burner starts every time. The bake burner is intermittent. First I removed and cleaned the igniter and still intermittent. When the bake wouldn't start, I could smell the gas, so I figure the problem had to be ignition. Considering the broiler would always start, I figure the spark control module had to be fine, so I replaced the bake igniter and the issue persists. Any help is appreciated. Thanks
1 Answer Hello Mcola. You need to look and see if the ignitor in the oven is sparking. If not, and the wiring and ignitor are good, you will need to replace the spark module WPW10331686. Read More...
Robert August 26, 2015 for Model Number wfg361lvq2 My bake burner lights momentarily, then cuts off. I switched wires on the valve & the broil burner lights when I set it to bake, but the bake burner still lights momentarily & cuts off again. What could be causing this?
1 Answer Hello Robert Try cleaning the burner and the orifice on the unit. If the issue continues, you will need to replace the gas valve on the unit. Read More...
Willy November 02, 2013 for Model Number SF362LXSQO The gas company disconnected my oven for CO . I'm surprised this model has no gasket or seal between the burner pipe and gas valve. How do I adjust the burner air/gas mixture ? I would expect the rotatable vents should correct this problem.
1 Answer Willy, You are correct, there is no seal or gasket between the oven burner tube and the oven gas valve. This is normal. On the burner tube, in the area of the "shutter" there is a small Phillips head screw or a hex head screw that needs to be loosened, so you can adjust the shutter, you may have to manipulate the shutter a few times before making any adjustments, the heat can cause the shutter to seize, and be very difficult to adjust. If you range operates on Nat. Gas, you want to open the shutter approximately 3/4 open, and adjust from there. If your range operates on LP gas, you need to start with the shutter full open, and adjust down from there. The proper flame and burn characteristics should be a double blue flame, with little to no white or yellow tipping, and the flame should be 3/4 to 1 inch in length (with the flame spreader removed) Read More...
David November 18, 2012 for Model Number GS563LXSB0 We had a grease fire in the oven. The fire was quickly extinguished and cleaned up. When we go to use the oven now, it never gets out of the pre-heat section of the process. The oven can be heard igniting and a flame seen from the vents for about a minute and then it shuts off. A few minutes pass and it ignites again and shuts off after a few seconds, occasionally you will hear just clicks and the oven does not ignite. It seems something was damaged by the fire. Does it sound like any part in particular? and something that can be replaced by a non-tecnician?
1 Answer Hello David, You may want to check you oven sensor to ensure that it is not defective. You should read 1100 ohms at room temperature. You would also want to check your gas valve coils to unsure that they are not bad. You should have 216 ohms resistance from broil to common and from bake to common. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Linda September 28, 2011 for Model Number whilpool oven My burners work fine but the oven when I turn it on there is no clicking nor no heat. Is tt the spark ignitor?
1 Answer Linda, Yes, it could be an issue with the spark module WPW10331686 , or the gas distribution valve coils WPW10293048. The DSI spark module is usually located in the control panel of the range, and somewhat simple to replace, depending on the model number(you forgot to attach a model number) Thanks and Good Luck Read More...
Carol August 02, 2011 for Model Number gs563lxsq1 My range is about 3 years old. About a 1 yr ago the burner for the lower (bake) part of the oven would randomly shut off while baking. There was the clicking sound but no re-igniting to keep the oven at it's cooking tempuratures. I determined it was the igniter and replaced it. Now it's doing the same thing again. It also does this while I'm trying to start the oven, clicking sound, but no ignition. Problem seems to have gotten worse in the last two weeks. Are these igniters so cheap that I have to replace them every year or is there something else wrong with my oven?
1 Answer Hello Carol. Check and see if the igniter is dirty and if it is sparking. If it is not sparking, you will need to test and see if it reads closed for continuity. If so, you may have a bad spark module WPW10331686. If it is open, you will need to replace the igniter WP9758079. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps.http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Guest February 25, 2011 My oven doesn't want to turn on. I thought it was the igniter but it's not. I replaced it and it still doesn't turn on? Would it be the burner?
1 Answer Sounds like you have a bad spark module. Here is the part number for you.WPW10331686 Read More...