Jimo December 17, 2013 for Model Number WMH1162XVQ2 What is the size of the filter offered for sale for this model. The existing regular filter is 5 3/4 x 12 7/8.
1 Answer JimO, the charcoal filter listed for the given model is part number 8206230A. From the images available the filter is approx. 5 1/2" x 5". The grease filter is part number W10208631A and is approx. 6" x 13". Thanks! Read More...
Cc December 01, 2013 for Model Number JMV9186WS-1 Will this part work for JMV9186WS-1? The dimension does not look correct.
1 Answer Hello CC. Based on the model number, 8206230A is the correct filter for the unit. Read More...
Hasan June 09, 2013 for Model Number YWMH1162XVS-2 I have replaced the filters but am still getting the message that I need to "clean / change filters". How can I make the message go?
1 Answer Hello Hasan! Please use the following link to view a copy of the owners manual available to your Whirlpool microwave model YWMH1162XVS-2. Refer to the Setting section, page 4, to reset the filter status. Hope this helps. http://www.whirlpool.com/digitalassets/MLPDF/User%20Instructions%20-%20W10219922A.pdf Read More...
Herb S. April 24, 2013 for Model Number KHMC1857WBL I want to change the grease filter on my KitchenAide Microwave Oven. I have been to just about every location in my area I can think of to purchase the filter without any success. Can you direct me to the right location?
1 Answer Herb, according to your model the grease filter is part number W10208631A. If needed, the charcoal filter is part number 8206230A. Unfortunately, we do not have information available on local parts companies. We do, however, have the items available for purchase. Thanks! Read More...
Marty S. February 20, 2013 for Model Number WMH1163XVS-1 I had the clean vent filter code pop-up on my over-the-range range microwave. I cleaned and replaced filters and the "Clean Filter" still pops up. Is there a way to reset it?
1 Answer Hello Marty, Reset the filter status after replacing and/or cleaning the filters. Touch Options or Setup control to reach the “Filter Reset” sub-menu and activate reset. To reset control, dis-continue power supply to the unit for 2 minutes and power it back up. If the problem persists, the control board WPW10211457 will most likely require replacement since the EEPROM read only programming information on it is probably corrupted. Read More...
1 Answer Hello Mike. Remove the vent off the top of the unit by removing the screws in the top. Then remove the old filter from the front and install the new filter 8206230A into the unit. Read More...
Margaret March 20, 2012 for Model Number gmh 3204xvq-1 This is in response to my earlier inquiry as to location of the charcoal filter. You stated it was located above the door and I had to remove the grill there is no grill on the top of my microwave it is solid above the door and no screws.
1 Answer Hello Margaret. Yes, the model number you provided has a grille. Here is the part number for it W10245216. It is located above the door, and the screws are in the top of the grille. Hope this helps. Read More...
Margaret March 19, 2012 for Model Number gmh3204xvq-1 In my earlier request I used the filter number instead of the model number model number is gmh3204xvq-1. Can anyone tell me how and where the charcoal filter is located in this microwave? HELP!!!!
1 Answer Hello Margaret. You will need to remove the grille at the top of the door to access and replace the charcoal filter 8206230A. It is located behind the grill in the air duct assembly. Hope this helps. Read More...
Jamie January 27, 2012 for Model Number GH4184XSS1 Where do I put the new charcoal filters on this model?
1 Answer Hello Jamie! Here is the information from the owners manual on how to replace the charcoal filter 8206230A. Hope this helps, thanks! To Replace Charcoal Filter: 1. Open the oven door. 2. Pull the vent grille forward and lift it out. 3. Push the filter back and clear of the rests, then lift the front of the filter up and slide it out. 4. Slide the new filter back and into place so that it rests at an inclined angle (about 45°). 5. Align the bottom of the vent grille into position, then push the top back until it snaps into place. Read More...
Sam January 18, 2012 My Whirlpool microwave displays message "Clean/change filter" I cleaned it real good, but the message still comes up. Do I need to reset something?
1 Answer Hello Sam! We will need your appliance model number to further assist you with this inquiry. Thanks! Read More...