Percy May 05, 2024 for Model Number MGR5775QDQ control panel not working has code either o 08 or 18 showing
1 Answer Percy,Try locating the tech sheet for your model for the meaning of these codes, it will likely be the control. Read More...
Nick April 10, 2018 for Model Number MGR5775QDS Oven will not shut off and gets very hot. I heard a pop noise before this happened. The only way to turn oven off is to unplug the stove from the wall outlet. Do I have a bad control board?
1 Answer Nick, Based on this information it would most likely be a faulty oven control board on the unit. Read More...
Robert D. October 17, 2016 for Model Number AGR5715QDQ Oven comes up to set temp.But after about 30.min. Temp goes off Control panel still reads set temp. Allready replaced oven igniter and oven temp. Senor. Broiler works fine.
1 Answer Hello Robert, You will need to run the diagnostics to see if there are any fault codes stored in the control. This is the most accurate way to locate an issue with an electronically controlled appliance of this nature. Read More...
Lory September 23, 2016 for Model Number MGR5775QDS Control panel on oven shows nothing but a continuous red light. Panel inoperative, but gas burners do ignite and work, oven light works when door open. I just can't turn oven on due to panel inoperative. Does this mean I have to replace the clock/overlay as shown on your website? Looking for cheaper solution.
1 Answer Hello Lory, I'm sorry but if there are no connection/harness issues, the only way to correct this issue is to replace the clock assembly WP74009227. Read More...
Nick May 24, 2013 for Model Number MGR5775Q DW Control panel shows only the clock working. Controls won't respond.
1 Answer Hello Nick. Based on the information you provided, the control panel is bad and will need to be replaced on the unit. Read More...
Ricky1842 May 20, 2013 for Model Number Mgr5775qds I replace my ignitor , and my oven still didnt come on, but my broil would come on. Whats my next step?
1 Answer Hello Rick1842. If the igniter is glowing, but no gas, you will need to order and replace the gas valve in the unit. Read More...
Atlanta Jim August 31, 2012 for Model Number mgr5775qdw Both my gas broiler and oven igniters do not work or go on. Would this be an indication that I need to replace the control module?
1 Answer Hello Jim, You need to check for 120Vac to the control. If none, verify the power supply. If 120Vac is getting to the control, check for 120Vac from the control to the ignitor. If none, replace the control WP74009227. If there is 120Vac leaving the control, verify all connections are clean and tight. Locate and replace broken wire. Read More...
Joe March 26, 2012 for Model Number agr5735qdb Oven and broiler stopped working. Is the electronic clock oven control & overlay the possible problem?
1 Answer Hello Joe. Check and make sure there is no broken or burnt wires on the unit and 240 volts is coming to the unit. Test and see if the clock is sending power to the elements during the bake or broil cycle. If not, you will need to replace the clock assembly WP74009227. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Fred February 25, 2012 for Model Number mgr5775qdb The control panel does not light up. Nothing works but the stove top does work. I've tried resetting the circuit breaker, but the oven still doesn't function.
Jack November 15, 2011 for Model Number MGR5775Qdb1 When you push the oven button to turn on, it lights the broil burner. I think it's the main board. What do you think?
1 Answer Hello Jack. Test and see if there is power coming to the igniter. If not, you will need to replace the clock assembly WP74009227. Hope this helps. Read More...