Gerry C. April 12, 2022 for Model Number WFW9200SQ02 Hello, Just recently purchased and installed a new rubber door boot from AppliancePartsPros for my Whirlpool front loading washer. After reassembly, my washer will not power up whatsoever. I've checked the obvious, plug outlet works fine and I checked the washer power line going into the MCU. I cannot find any videos on how to test the MCU. All the connections I had to disconnect during the boot replacement only go into their assigned slot so I couldn't have miswired anything during reassembly. Any thoughts before I call a local tech? Thanks.
1 Answer Gerry, the noise filter WPW10367632 would need to be tested for 120VAC coming in from the power cord and 120VAC going out to the main control WPW10169230. If there is voltage going in but not leaving it, the noise filter would need to be replaced. If there is voltage at both sides, the next step would be testing the power going to the user interface W10319816 from the main control. On the wire connector UIP3, there should be 5VDC when testing from the wire at pin 2 to the wire at pin 1. There should also be 12VDC when testing from the wire at pin 2 to the wire at pin 3. If there is not voltage at either of the test points, the main control has failed. If there is voltage at both points, the failure would be in the user interface. Read More...
John Lippolis October 03, 2018 for Model Number WFW9200SQ02 I can only select certain wash cycles "Normal" does not light up on dial and when start is pressed, only get beeps. Display show dashes but no error codes. Heavy duty cycle works. When dial is turned to sanitary the delicate cycle lights up. Question - Do I need part # AP4539793 or AP6016145. Both are listed as Control boads. Thanks
1 Answer John, At this point, and based on the post description and information you'll need the W10319816 / W10319816 Electronic Control Board / User Interface. The part is in stock and available at this time. Thanks, Read More...
Mike G December 03, 2015 for Model Number WFW9200SQ02 My wife stopped the washer mid cycle to add an item. The washer started to drain a bit and then shut off. There was still some water in the bottom. The unit doesn't turn on at all. No lights or sounds are coming from pressing the buttons. I tested the outlet and it's perfectly fine and the dryer works on both plugs. I'm not sure if this is the control board or the control panel and I don't know if running the diagnostic will show anything since it's not powering up. What are your thoughts?
1 Answer Hello Mike. You need to test for power to the board and if it is there, you will need to replace the control board on the unit. Read More...
Kim June 15, 2015 for Model Number WFW9200SQ02 My washer stopped washing completely. Clothes in the washer were still wet - looks like it didn't finish draining. I checked the filter and cleaned it out. I also took the top cover off and looked for loose connections. I turned the power supply off and tried again. Still nothing. I put in on the drain spin cycle - the water started to fill in and then it stops - doesn't move to the next cycle. Could it possibly be the electronic control board that is the problem?
1 Answer Kim, While it is possible that the control board is faulty, it is also possible for the door latch assembly to be an issue. You will want to access the tech sheet which is located in the unit and put the unit into diagnostics. Check to see if there are any error codes that are stored. This will guide you to what may be going on with the unit. Read More...
Mark S. December 09, 2012 for Model Number Whirlpool WFW9200SQ02 The door will not latch. It appears to be in the locked position. The front panel has no functions but I can get the diagnostic tests to run, however it does not show any error codes. Is the problem with the central control unit and is the right control #W10169230?
1 Answer Hello Mark, It appears that the control board is faulty. You would need to replace the control WPW10169230. It may also be necessary to change out the door lock assembly. If a switch inside the lock is faulty it will could have caused the board to go bad. When you install the new board. Just try the unit 1 time. If it does not work then replace lock WP8183270 and do not try to continuously get it to work. Read More...
Csshull June 10, 2011 for Model Number WFW9200sq02 Panel is blank. Pressing the power button give 3 short beeps. When I run diagnostics (pwr pressed for 4 seconds, then off for 4 seconds and repeating 4 times) the panel lights up runs some tests that I cannot decypher starting with C:00, ending with F 70. The F 70 indicates I should replace the CCU (central control unit) Is the ccu 318981 or 539793?