Brian M. February 14, 2017 for Model Number WFW8410SW03 Installed a CCU on the washer. All the lights and dial are one off from what they should be when selected. Examples: Quick Wash should be 24min and reads 54min which is the Normal Wash time. Can only select loud or soft for chime but can not turn off.
1 Answer Brian, You will want to double check the wiring connections on the CCU from the user interface. If this checks ok then you may have received a defective CCU. Read More...
Nick November 28, 2016 for Model Number WFW8410SW02 Hello. Like others on this board, my washer starts up on any cycle I select, but then stops after a few minutes. Where my issue is different is that I do not get any error codes - the washer just completely powers off (door lock is released, too). Is there any other fix other than replacing the main control board?
1 Answer Nick, With the unit just powering down after a couple of minutes you will want to check to see if there is power going to the water valve if the unit does not fill with water. If there is power to the valve but does not fill then a faulty valve would be the cause. If there is no power then the control board would be the issue. Read More...
John September 25, 2014 for Model Number WFW8410SW03 I have a problem with my washer. The LED screen on my front load washer shows the number 1 and does not show any other number when switching between cycles. The heavy duty cycle of 90 minutes is the only one that works. I already checked the water pump and its normal as it does drain. Can you please help me resolve this problem? Thank you.
1 Answer Hello John, As per the tech sheet: 1.Press PAUSE/CANCEL on the touch-pad twice. 2.Check the touch-pad/LED assembly by selecting different cycles and changing the modifiers and options available to confirm the touch-pad/LED assembly is responding.3. Unplug washer or disconnect power.4. Make sure that all wire harness connections to CCU are not broken or with wires detached, and that connector internal pins are visible.5. Drain the unit, and then check that the drain hose and drain pump filter are clear of foreign objects.6. Plug in washer or reconnect power.7. Verify unit operation by running a Service History Mode & Diagnostic Test or any cycle. If the unit will not go into diagnostics or no other problems are found, there could still be a problem in the CCU WPW10679602. Read More...
Lnew3909 July 19, 2013 for Model Number WFW9400SW As soon as I turn on the washer, it sits there for a few minutes not taking in water, then it displays an error code f28 but the door is not released. WFW9400SW Duet. What do I need to do?
1 Answer Hello Inew3909. The communication between the Central Control Unit (CCU) andthe Motor Control Unit (MCU) cannot be sent correctly. Possible Causes/Procedure1. Unplug washer or disconnect power.2. Check wire harness connections to the MCU, the motor, andCentral Control Unit (CCU).– Check connections of the CCU board within the housing.– Make sure all grounding switches are engaged.3. Check the drive system for any worn or failed components.4. Plug in washer or reconnect power.5. Verify CCU operation by running a Diagnostic Test or anycycle.6. Check the MCU by looking for operations of the drive motor.7. Check the drive motor for powered rotations.8. Check that the serial harness at the MCU is not mountedupside down. The wires should be to the left when facingthe MCU connectors. Read More...
Gerald B March 27, 2013 for Model Number WFW8410SW02 our washer finishes the wash, and the clothes are still soaking, as if the spin did not finish. Often resetting the washer to Drain/Spin and restarting a couple of times gets it to finally spin the clothes dry. The repairman said that it was the motor W10140581 and/or the motor controller W10163007 so I replaced both of them with new products. It has not fixed the problem. I don't know if the new motor controller is bad also. I am considering replacing the unit controller W10160255 with the replacement W10205842. Please help! Thank you!
1 Answer Gerald, You will want to check the drain for debris that could cause a slow drain. Also check the tube at the bottom of the tub. If things get clogged in drain line and the water does not drain fast enough it will cause the unit to not spin out properly. Read More...
Ed June 03, 2012 for Model Number WFW840SW01 Which part labeled Control Elec (# 3 or # 6) is the Central control unit?
Ivan December 11, 2011 for Model Number WFW8410SW01 MY WASHER START WASHING AND AFTER LIKE 10 MINUTES STOP RUNING AND CANCEL THE WASH AND CODE F20 WOULD COME UP DID YOU KNOW WAS THE PROBLEM OR THE PART THAT FAIL?
1 Answer Ivan, The "F20" error code, indicates the main control board is not "seeing" water enterring the washing machine, The first thing to check are the fill hose and fill val;ve screens for debris and clogs, and flush both the water supply faucets. Disconnect the air hose from the water level switch and blow in the hose to clear any debris or deposits in the hose. Then check the washer for a proper fill and opeeration. Good Luck and Thanks Read More...
Bob October 10, 2011 for Model Number wfw8410sw01 Washer runs for about 2 minutes then has F01 fault on display. Door is locked and have to power down to reset fault. Checked all wiring for control board and appears good. no clogs found anywhere. F01 fault happens on any cycle that is selected.
1 Answer Hello Bob. The F01 code means: The pump driver fails to activate/One of the main relays is not working properly/A communication error between the Central Control Unit (CCU) and the EEPROMonboard the CCU occurred. - Check for loose power outlet. A loose power plug in the wall can createline noise and issues.- Check if washer is on a dedicated circuit. Other devices on same circuitcan create line noise and cause this issue.- Unplug washer or disconnect power.- Make sure that wire harness connections from the CCU are not broken or with wiresdetached, and that connector internal pins are visible.- Make sure all green wires (ground harness system) are not broken or detached.- Make sure the two ground switches are pressed correctly by the toe and rear panels.- Make sure all connectors are fully seated.- Plug in washer or reconnect power.- Check for power going to Central Control Unit (CCU) by listening for a click in theCCU when unit is plugged in washer or when reconnecting power.- Verify unit operation by performing the Diagnostic Test. See page 5.- After the diagnostic test has finished, unplug washer or disconnect powerand wait for 15 seconds. Read More...
Marcia September 18, 2011 for Model Number wfw84105w01 Machine won't come on at all is there a reset button
1 Answer Marcia, Sorry but, No there is no reset button. You need to make sure the power cord is not loose in the outlet, and there's power at the outlet, before you remove the top of the washer(move the washer out enough to get to the three screws across the back of the top, and slide the top backwards 1 or 2 inches and lift it up and off the cabinet) and start looking and checking for damaged wires and components. Thanks and Good Luck Read More...
A1alfa August 01, 2011 for Model Number WFW8410SW02 Periodically, the machine would stop running at the rinse cycle and code f28 would come up. Couldn't even open the door. Pull the plug and repower up, set it to the rinse cycle instead of the wash cycle, starts up and sometimes it would complete the cycle. I am suspecting it's the ccu and thinking of replacing it. What is your opinion?
1 Answer Hi Alalfa. The communication between the User Interface board and the Central Control Unit is bad. Check all wires between interface, CCU, Door switch, motor controller and motor. If they are all fine then check all the ground switches on the lower front and back of the frame. If all of these are correct, Then replace the CCU part # is WPW10679602. Thank you. Read More...