Anne January 24, 2017 for Model Number WGD6400SB1 I have a Whirlpool Cabrio gas dryer model # WGD6400SB1. When I try to start it I now get a code F2 on the display panel and then the dryer will not start.What do I need to fix the dryer?
1 Answer Hello Anne. F-02 flashes when there is a stuck button or user interface mismatch. You will need to replace the control panel. Read More...
Mark January 19, 2016 for Model Number WED6400SW0 What is on the back of Whirlpool Part No. W10110325?
1 Answer Hello Mark. This is the control panel assembly and it has a sticker on the back with the warnings. Read More...
Mark January 16, 2016 for Model Number WED6400SW0 Does this part also include the grey plastic component that the circuit board snaps in to. I have the same problem with the broken start button. All I need is the gray plastic assembly, without the control board but I don't want to have pry the assembly off of the console panel. If a new console includes the gray assembly then I am in good shape. Please advise.
2 Answers Mark, The part that would have the gray plastic with the buttons on it would be the electronic control WP8563974. Unfortunately the gray plastic is not available separately. Read More...
Mark January 16, 2016 for Model Number WED6400SW0 Does this part also include the grey plastic component that the circuit board snaps in to. I have the same problem with the broken start button. All I need is the gray plastic assembly, without the control board but I don't want to have pry the assembly off of the console panel. If a new console includes the gray assembly then I am in good shape. Please advise.
2 Answers Mark, The part that would have the gray plastic with the buttons on it would be the electronic control WP8563974. Unfortunately the gray plastic is not available separately. Read More...
Edward December 11, 2014 for Model Number Whirlpool WED6400SW0 My dryer timer has a problem. For example, I selected "normal" and it should be 40 minutes long. It shows 40 minutes in the beginning, but it did not count down correctly and finished around 25 minutes. Which part should I change? Thanks
1 Answer Hello Edward, If the exhaust thermistor WP8577274 ohms out properly, (10K ohms), this is most likely an issue with the electronic control WPW10111616. Read More...
Christan June 30, 2014 Question asked prior: Hello, for WHIRLPOOL Panel (Part Number: AP3964397), does this include the gray plastic panel on the inside which holds the plastic pieces that push against the buttons on the electronic circuit board? To answer your question (does the user interface have those buttons), the user interface board DOES NOT have the grey plastic part with the "liaison" buttons that go between the front interface buttons and the user interface circuit board. Does one have to purchase the entire cover assembly to get that one piece? Seriously... that's unbelievable that I have to pay for the whole thing because a piece of plastic broke off on a non-integral piece on that cover.
1 Answer Christan, Unfortunately the manufacturer only supplies the part as a complete assembly and would have to purchase the complete panel in torder to get the buttons that go between the user interface and the circuit board. Read More...
Jim C. April 06, 2014 for Model Number wed6400swd Machine has power. All functions work. Just wont start when start button is pushed. Not sure what I need to order.
1 Answer Jim, You will want to check the door switch for continuity when the door is closed and check the blower thermal fuse to make sure that it has continuity. If either one does not have continuity then that is the issue and the part would need to be replaced. If they check ok then the user interface would most likely be the issue. Read More...
Sandy April 27, 2013 for Model Number wed6400sw0 I need to order a User Control interface #8563974 because the plastic piece behind the Start button broke. However, I'm not sure how I'm going to get this piece pryed off of the console board. (W10110325). It looks like it's been glued on and if I'm looking at this correctly, those two pieces are purchased separately. HELP!!!!
1 Answer Sandy, To remove the user interface you will first unplug power to the unit and remove the control panel. Disconnect the user interface cable connector from the machine control board, connector P5. Pull The knob off the shaft and remove the 3 screws in the UI board cover. Using a flat blade screwdriver, pry the 2 locking tabs out, and unclip them, then remove the UI cover from the console. You will then need to remove the encoder by lifting the locking tab and turn the encoder to the left (counter clockwise) as far as it will go. Lift the encoder straight up so that the shaft slides out of the rubber console seal. and remove it from the console. NOTE: Do not flex the encoder ribbon cable wires that the UI or they could break. Using a flat blade screwdriver you will then carefully pry the front edge of the user interface board up, then pull the board forward, and remove it from the console. Read More...
Will July 17, 2012 for Model Number wed6400sw0 Hello, for WHIRLPOOL Panel (Part Number: AP3964397), does this include the gray plastic panel on the inside which holds the plastic pieces that push against the buttons on the electronic circuit board?
1 Answer Hello Will! I believe the part you are speaking of comes equipped with the electronic control itself. Please view part number WP8563974 to verify this is the item needed. Thanks! Read More...
Nick May 29, 2011 for Model Number Part Number: AP3964397 Is index 5 Panel a complete assembly including the electronic control circuit board (PN: AP3957593) and all necessary parts? At this price, I would think it should be a complete assembly.
1 Answer Hello Nick! No, the control panel WPW10110325 does not include the circuit board WP8563974. It is the control panel only. Thanks. Read More...