Tony December 04, 2016 for Model Number JJW9630DDB The heating element burned in half so I replaced the heating element, fan, and fuse block. Would this burn out the control panel? The lower oven works fine.
1 Answer Hello Tony. If it not likely, but you can test for power from the control board to the element. If it is there, then the board is fine. If not there, then the board is bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jeffrey August 20, 2016 for Model Number JJW9627DDS I have a Jenn-Air model# JJW9627DDS. My wife used the oven in the morning fine and turned it off after cooking. Later that day she noticed that the display panel was completely dead. Checked circuit breaker which is fine.I measured voltage from L1 to neutral as suggested in another post and it registers 121.8 vac.It also states that I should check the High Limit Thermostat to make sure that it is not blown? Not sure where this thermostat is and how to check weather or not it is blown? Any instruction is appreciated. Based on my findings so far any thoughts on weather or not it may be the control board? Many thanks for the help !
1 Answer Jeffrey, If you have 120 vac to the control board but here is no display showing then this would be a faulty control board WPW10169131. Read More...
Frank M August 26, 2015 for Model Number JJW9630DDW The setup and some of the numerical buttons on the front do not operate. I see one part number on http://www.appliancepartspros.com/control-panel-internal-parts-for-jenn-air-jjw9630ddw.html number 2 Electronic Control Panel. When i pulled the oven out of the cavity and removed the glass touch assembly i noted three boards behind the glass panel but the schematic on the above web page and also noted that several items are not available not longer manufactured. How does a lay person determine what piece is broken and how to i find replacements for a part if it is not available from the manufacturer?
1 Answer Hello Frank. The part your needing 74011943 has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Carol H. May 08, 2015 for Model Number JJW9627DDS I have a jennair double oven, about 4 years old. The bottom oven works fine. The top oven, preheats to the desired temperature, then slowly declines. If I set it to 350, it will preheat to that value, then slowly decrease to about 200. Never kicks back on to maintain the heat. Had an appliance man come out, paid him $120. told me that everything looked good, so he thought it was the control board, to the tune of $950. Any advice? Is the control board hard to replace. I have some experience with circuit boards, but definitely not a pro. Scared to spend 3-400 on new board… Bottom oven is fine. Replace the whole thing???
1 Answer Carol, It's more likely to be a more "minor" inexpensive component. If needed the ERC/Clock WPW10169131 is not a very difficult repair to make. Before you start with the control board, you may want to replace the oven temp. sensor WP74008369 after years of service or a self clean cycle, the sensor can loose it's calibration and produce erratic and slow / low temperatures. If everything checked out OK and proper for the servicer, you may want to start there. It is also a somewhat easy repair to make, remove the racks, remove two screws and slowly extract the sensor and harness. unplug the connector and reverse the procedure. Read More...
Reed December 04, 2014 for Model Number JJW9630DDB Push control to bake or convect or clean...oven begins to warm up then shuts off. It warms up a little then shuts off. Try again does the same thing. Will not stay on to reach any kind of temperature. Was working fine last week. Any ideas? Control panel?
1 Answer Hello Reed. Make sure the breaker is good and if so, replace the control board on the unit. Read More...
Ed N October 30, 2014 for Model Number JJW9627DDB My Jenn-Air double wall convection oven exhibits fully functional panel and upper oven; Lower oven will engage and heating element gets hot, but then around 110 deg. F, panel indicates "fault detected" and displays error code 4d22. Displays 'control has detected a fault that affects performance and has disabled that feature.' Then lower oven remains disabled. When 220v breaker is cycled, it will repeat this process. What sequence of parts replacement would you advise trying? Thanks Very much, Ed N
1 Answer Ed, The 4d22 error code is an indication of no reverse airflow fan rotation and will occur when in cook or clean setting. This is an indication that the fan is not operating when the temperature gets to a certain point. This would be caused by the fan either not getting power from the control board or the fan being faulty. You will want to check power to the lower fan motor. If power is present then the fan is faulty and if no power present then the control board is faulty. Read More...
David December 31, 2012 for Model Number JJW9630DDB After a power outage the oven does not turn on. Absolutely nothing. I'm suspecting the control board. Are there any other parts that might be at fault?
1 Answer Hello David, You may want to check the High limit thermostat to make sure that it is not blown. Also check L1 to neutral on the control board to make sure that you are getting power to the control. If there is 120 vac between L1 to neutral then replace control board. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Stephen K November 02, 2012 for Model Number JJW9630DDS On the series 18, the control panel works except for the area controlling the lower oven. Hitting those buttons only beep, nothing else happens. Can part of a control panel go bad, or is this somethng else?
1 Answer Hello Stephen. Based on the information you provided, it sounds like the control panel is the issue with the unit and you will need to replace the control panel. Read More...
Stephen K. November 02, 2012 for Model Number JJW9630DDS On this double oven, series 18, The control pad that controls the bottom oven stopped working all at once. It just makes a beep. The part that controles the top oven works fine, and the right hand side of the control panel works fine. The bottom oven has never shut correctly The oven light seems to always be on because the door is usually ajar. The oven ligh comes on when the door opens, but not when the oven light switch is used. Do I need a complete new control panel board?
Gian D. August 29, 2011 for Model Number JJW9627DDS Is it possible to get a schematic diagram of the card. The power is coming to the card, but the second card is not getting power.
1 Answer Hello Gian! Are you needint the wiring information? If so, please view the following links to view the wiring diagram for your JJW9627DDS model. Thanks!http://www.appliancepartspros.com/partsearch/frame_diagram.aspx?diagram_id=28429981&pkw_=basket&model_id=5177238&NewWindow=1Series 19 FRC: http://www.appliancepartspros.com/partsearch/frame_diagram.aspx?diagram_id=28429982&pkw_=basket&model_id=5177238&NewWindow=1Series 19: http://www.appliancepartspros.com/partsearch/frame_diagram.aspx?diagram_id=28429984&pkw_=basket&model_id=5177238&NewWindow=1 Read More...