Jb June 11, 2013 for Model Number MDC4650AWW Water leaks from between coupler and faucet adapter. Coupler appears to be seating correctly and holds under pressure. What do we need?
1 Answer JB, You will need the seal in the coupler assembly which is not a replaceable part. You would need to replace the coupler WP99001868. Read More...
Fancy April 30, 2013 for Model Number MDC4650 I have a portable dishwasher and the hose keeps popping off at the sink. Am I right in thinking I need to replace the hose which has a crimped end with the female coupler? If so is the price listed include free shipping?
1 Answer Hello Fancy. If the couple on the faucet is good, you will need to order and replace the hose set on the unit. Shipping is extra. Here is a link to our flat rates. http://www.appliancepartspros.com/customerservice/shipping.aspx Read More...
Mary March 23, 2013 for Model Number MDC 5100 AWW My dishwasher will not fill with water, what replacement part will I need for repai?
1 Answer Mary, You first need to check and make sure the flaot WP99002363 is not stuck or held in the up position. Then you;ll need to remove the lower access panel and,toe kick panel and check the water fill valve 903406 and hoses. Read More...
Justin M. March 11, 2013 for Model Number maytag pdc3600awx On your coupler hose assembly, the coupler has a sort of snap ring that comes off to allow you to see the internal parts of the spring and the four plastic snaps that lock on to the facuet adaptor. These are made of cheap plastic that gets hot and erodes till pops, it falls off and all your precious hot water goes down the drain. So please, please, tell me that you can buy the four plastic snaps that can be replaced in 2 minswith no tools and can't cost more the 50 cents to make vs an expensive replacement hose and coulper. Are they available and if not, why?
1 Answer Hello Justin! Unfortunately, the manufacturer does not offer any parts separate from the coupler and hose assembly WP99001868. I do apologize for the inconvenience. Read More...
Dan February 19, 2013 I bought a replacement coupler and hose assembly for a portable dishwasher. ORDER SUMMARY Order Date: 2/14/2013 Order Number: 3155802 AP4114683 (99001868) Coupler & hose assembly 1 $52.28 This hose was used because it was cross referenced as a substitute/replacement for the hose that was on the dishwasher I was working on: Part Number 99001868 (AP4114683) replaces 99001306, 99001868. The hose is now installed, but this coupler won't lock onto the part which is attached to the kitchen sink faucet, but the old hose does just fine. Clearly this hose is not compatible with that part. Q1: What is the part number for the piece which attaches to the kitchen sink faucet (where the aerator normally goes) that I now need to make this work? Q2: Might it make sense to just pair up that part with this hose and coupler set automatically so that people don't end up with this delay and with having to place two orders and pay two shipping fees? Thank you, Dan
1 Answer Dan, The corresponding faucet adapter part number is WPW10254672 . If you haven't yet, remove the present adapter from the faucet, and insert it into the new hose coupler to see if it seats and locks. Your issue may be the clearance at the faucet,not the adapter or coupler. You may want to purchase an areator adapter at the local home improvement center. At AppliancePartsPeos.com, we distribute the parts as we recieve them from the manufacturer, Your idea would be a good one, but we're sure the manufacturer has a reason for not making certain components a "packaged deal". Read More...
Randy January 19, 2013 for Model Number 66517769k600 The faucet connector blows off, the "hard" o-ring came off. Replaced the o-ring with a black "rubber" o-ring . The problem is still occurring. What to do next?
1 Answer Randy, Check and make sure the internal retainer ring "locks" into position, when the coupler ring is in the up position, a dab of "vaseline" may be needed to loosen the retainer ring, so it locks and unlocks properly when attached to the areator/adapter. Also check and make sure the adapter/areator WPW10254672 is not distressed, and properly installed. Read More...
Mg December 08, 2012 for Model Number Maytag MDC4809AWB0 The coupler on my dishwasher is leaking to the extent that it is not at all useable, though it was just replaced a year and a half ago. Do I need to replace the whole coupler + hoses, or can I just repair the coupler? It is a Maytag, model MDC4809AWB0. Either way, which part(s) do I need?
1 Answer MG, you will need to replace the coupler assembly. Your part number is W10842407. Thanks! Read More...
Debbie November 17, 2012 for Model Number MDC4650AWW Due to tight space issues, I need longer hoses. How long is the part #99001868?
1 Answer Hello Debbie, the hoses are considered 8 foot hoses but they measure about 8 feet, 3-1/2 inches. Hope this helps! Read More...
Dawn October 17, 2012 for Model Number kenmore portable dishwasher- 665/17439001 The dishwasher was hardline and now I need to turn it back into a portable. I need the drain and fill hose kit and a faucet adaptor coupling. Do I need specific ones? Thank you for your help and information.
1 Answer Hello, the fill hose is WPW10273574, power cord 3371542 and the coupling is WPW10254672. In case you need the casters it's part number WP3370639. Thanks! Read More...
Marlene September 12, 2012 My question is,my connection to faucet keeps blowing off,i am assuming i need a Whole new Coupler and Hose set? Problem is i can't figure out the proper serial # for my Whirlpool portable dishwasher,here r all the # i could find,MDC4650AWB - 42720969NJ and E71195- Type- 779-0.Ty very kindly,i will be patiently waiting....
1 Answer Hello Marlene. Based on the information you provided, you need to order WP99001868 for the unit. Read More...