Newnanny March 08, 2012 for Model Number GHW9200LQ Does this part include the top with all the holes in it where the water flows thru to dispense the detergent/softener/bleach?? I have 2 of these washers and BOTH of them I am having a problem getting the water to flush out my detergent (both liq and powder)... no problem with softener or bleach... thought maybe the holes might be limed up since we have hard water. Any suggestions??
1 Answer Hi Newnanny. Look at the detergent container part # WP8181722, and the siphon cap part # 8182665 to see if they are clogged. Use the sink to clean and flush out both parts for proper flow. If all of these parts and the detergent separator part # WP8181730 need periodical cleaning to insure the proper flow. The dispenser assy. part # WP8182704 does not include these parts. Thank You. Read More...
Mark February 16, 2012 Does the dispenser assembly (AP3861933) come with the spring loaded actuator on top?
1 Answer Mark, no the dispenser assembly WP8182704 does not include the spring loaded actuator. To make sure we provide the correct parts for your unit we will need your appliance model number. Thanks. Read More...
Steve February 08, 2012 There are 2 plastic nipples on the back of the dispenser. Mine only has a hose on the top nipple. There is water leaking from the bottom nipple. Should there be a hose hooked up to the bottom nipple?
1 Answer Hi Steve. If the back , bottom dispenser nipple is leaking, then that means there is a internal disp. leak and the water path is being diverted. The whole assy. needs replaced. Part # WP8182704. Thank You. Read More...
Greg November 06, 2011 for Model Number Whirlpool GHW9200L Which cycles do the 4 numbers on top of the Dispenser assembly represent? My washer started in off on 1 then immediately went to 2, stayed on 2 when rinse started, back momentarily to 1, then back to 3, then finally to 4. I was reading one of the above answers that said 1 is soap, 2 is bleach, 3 is softener, and 4 is flush. My softener did not release until the needle was on 4. Is that correct for this machine? The clothes do not seem to have the smell nor softness of the fabric softener on them when done. Thank you.
1 Answer Hi Greg. You are correct. 1-detergent, 2-bleach, 3-fabric softener and 4-rinse. The most common failure is that the softener /bleach siphon cap will get clogged and interrupt proper flow. Part # 8182665. Thank You. Read More...
Sandra August 23, 2011 for Model Number GHW9100LQ1 My dispenser assy is leaking because we cracked it when removing a hose to replace another part (flow meter). When I look in my washer, this appears to be difficult to replace due to space constraints and the spring loaded part on top. I've replaced other parts without issue (pump, water level sensor for example). Is it just tedious or is it complex to replace this part?
1 Answer Hi Sandra. This is a relatively easy replacement part. You will need a small pick tool to assist in release the clasp lock that hold the small elect. connectors. Then a adjustable channel lock type wrench for the hose clamps.The dispenser assy. is part # WP8182704. Thank you. Read More...
John In August 10, 2011 for Model Number GHW9100LW0 Does replacement part "Dispenser Assembly (17)" Include the following parts: "Detergent Drawer (21)" "Detergent Container (22)" "Bleach/softener siphon (23)" "Dispenser separator (24)" "Pre- wash Cover (28)" Thanks for your assistance.
1 Answer Hello John. Yes, the dispenser assembly WP8182704 includes those parts. Hope this helps. Read More...
Dave May 19, 2011 for Model Number whirlpool duet front loader washer AP3861933, is this the correct part number for the door assembly on the detergent/softner/bleach fill drawer?