Karen August 11, 2017 for Model Number WP8182704 I just replaced the boot on my kenmore Elite HE3 upright and there is a small black tube running from the Dispenser assembly to the front. this is on top of the boot and is leaking. I can find nothing that shows where it actually goes or what it is called. Can you help me.
1 Answer Hello Karen. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Lisa June 08, 2017 for Model Number 110 42822 203/serial CSP4809854 Distribution nozzle fell out when I was cleaning my Kenmore HE3 washer. How do I put it back in? Can I use the washer without it?
1 Answer Lisa, You could use the washer as is, but The fabric softener and bleach will not dispense properly and could damage the clothes or articles in the washer. You'll need to get the dispenser assembly WP8182704 replaced as soon as possible. Read More...
Rob August 25, 2016 for Model Number WTW7340XW2 Water is leaking from under the lid, left front of washer. Seems to be splashing out of the detergent dispenser tray during fill cycle. Also noticed that water is splashing out of bleach dispenser on left rear of machine, causing the lid, washer top and lid hinge to rust. What could be causing these problems?
1 Answer Hello Rob. You will need to order and replace the dispenser WPW10187307 on the unit. Read More...
Sara August 16, 2014 for Model Number GHW9100LW1 At times there is water still left in the washer after the load is completed. What causes this and why is this happening?
1 Answer Hello Sara, This is either going to be a water valve WP8181694 issue or control board WP8182221 issue. Read More...
Mark August 05, 2013 for Model Number wf328aaw/xaa Can a bad dispenser assembly cause the nf code to appear only before rinse cycle?I have replaced both of the inlet valves and the problem is the same those were the pats suggested for the nf code apearing
1 Answer Mark, A dispenser issue would not cause the NF error code. You will want to check the following for this error: Check the water valve wiring harness. Check whether the water supply valve is clogged with foreign material and whether water is supplied properly. Check for reversed fill hoses Check water temperature, if sensed as higher than 50 °C in the Wool or Lingerie cycle it will create error. Check the relays, if they operate correctly replace the Main PCB. Read More...
William L April 25, 2013 for Model Number ghw9150pwo On control panel the control lock lamp is lit ,unable to get washer to work. tryied unpluging it for 2 mins,tried pressing cancel button ,cleaned filter basket .
1 Answer William, The control lock can be disabled by pushing the end of cycle signal for 3 seconds until the control locked status light turns off. Read More...
Brad B January 03, 2013 for Model Number ghw9150pw0 I replaced the bellow because it was leaking at the bottom. After putting the washer back together, I started the washer back again. While it starts filling the drum, water is running from the front to the back on top of the dispenser. Not sure how this is happening or how to stop it.
1 Answer Hello Brad, It sounds like you may not have gotten your hoses to the dispenser reconnected tightly or the tube that comes to the bellow is kinke and forcing water back up over the dispenser. Double check all hoses and connections. Read More...
Quant November 29, 2012 for Model Number GHW9200 My Whirlpool washer dispenses the softener too early. I find that water overflows/splashes/leaks into the softener container while the washer is filling water into the detergent containers. The actuator arm moves correctly from positions 1 to 4 at the correct times during the cycle. I either have in internal leak or a blockage from years of use, right? Do I replace the Dispenser Assembly (8182704) or the Dispenser Actuator (8181723) ?
1 Answer Hello Quant, You may want to pull the dispenser assembly and try to clean assembly. It sounds like the water distribution lever is not working properly. It may be gummed up causing the issue. If this does not work then you would want to replace the Actuator motor WPW10665207. Read More...
Newnanny March 08, 2012 for Model Number GHW9200LQ Altho part# AP3128798 says it is the detergent container, it actually houses the area where you put the softener and bleach.... I am having problems getting my 'detergent' (BOTH liquid and powder) to wash out of the dispenser on the 'other' side... ALL of the parts in this 'drawer' assy have been cleaned and flushed out. I can actually 'manually' flush out the detergent each wash cycle is I choose to (I would rather not). Is there some place 'above' the drawer assy where the water flows thru before it gets to the 'detergent' side of the drawer that could be the problem?? Sorry for the confusion... Thanks for your help!!
1 Answer Hi Newnanny. Look at the detergent container part # WP8181722, and the siphon cap part # 8182665 to see if they are clogged. Use the sink to clean and flush out both parts for proper flow. If all of these parts and the detergent separator part # WP8181730 need periodical cleaning to insure the proper flow. The dispenser assy. part # WP8182704 does not include these parts. Thank You. Read More...
Newnanny March 08, 2012 for Model Number GHW9200LQ Does this part include the top with all the holes in it where the water flows thru to dispense the detergent/softener/bleach?? I have 2 of these washers and BOTH of them I am having a problem getting the water to flush out my detergent (both liq and powder)... no problem with softener or bleach... thought maybe the holes might be limed up since we have hard water. Any suggestions??
1 Answer Hi Newnanny. Look at the detergent container part # WP8181722, and the siphon cap part # 8182665 to see if they are clogged. Use the sink to clean and flush out both parts for proper flow. If all of these parts and the detergent separator part # WP8181730 need periodical cleaning to insure the proper flow. The dispenser assy. part # WP8182704 does not include these parts. Thank You. Read More...