Alan July 25, 2020 for Model Number wfe366lys0 I searched on the model number and obtained the parts diagrams that were presented, with the correct model number at the top of the page. I ordered part number 10 on the door page, door hinges which came yesterday.(order number 11822335). The part number of the replacement parts supplied is W10347466 (AP5325898). I started to replace the broken hinge this morning and found that the replacement hinge is not the same as the one in the door, It is shorter in length, both body, by an inch and a half) and spring (by 3/8 inch). Also the hinge lock assembly is different with there being no visible lock on your replacement part. In the oven door both springs had a red stripe whereas one of the springs in the package had a yellow stripe. So, are the replacement hinges you sent compatible with this range model ( wfe366lyso)? If not, why did they arise as a part for this model from the explosion diagram? If they are not compatible please send me the correct parts for this model. I would be grateful if you could also send a prepaid shipping label for the return. . thank you alan upshall
1 Answer Alan, According to the manufacturer, the hinges that you received are the correct hinges for your unit. They may look different but should still work the same. Read More...
Paula June 23, 2017 I got it all put back together--and it works!--but now I have another question. When I put the baffle back on, it doesn't seem to be level (it appears to lay slightly higher on the right side). When the oven is lit, the flames seem larger on that side too, looking from underneath. Since I didn't bend the baffle, do I assume that is normal or do I need to try to make it level? Thank you.
1 Answer Paula, You will want to try to get the baffle level from one side to the other. Read More...
Paula June 19, 2017 for Model Number FGB24L2ASA I am trying to replace the igniter. I took off the oven door with no problems, but cannot get it back on. The lock will not go back to the closed position. It seems to be caught in the position for door removal. I've been trying to figure it out for a couple of hours with no luck...
1 Answer Paula, If you kind of pull down on the door slightly and use a flat blade screwdriver you should be able to get the door lock part loose to get the door back in place. Read More...
Randall B February 26, 2017 for Model Number W10347466 Does the package for $35 come with 2 hinges or just one hinge?
Ryan M August 23, 2015 for Model Number JBP65S0M2SS Hi there. I'm checking to see if this oven hinge will work on my General Electric oven model JBP65S0M2SS? Thanks, Ryan
Doug May 21, 2015 for Model Number KEBC207KSS05 I replaced both hinges but there is still a 2" gap when shutting the oven door. Please advise. Can you send me the answer to my email? Thank you.
1 Answer Doug, It sounds like the hinges may not be in place properly. You will want to pull the door and make sure that the hinges are extended and held in place by the swivel hook. With the hinges extended then you would insert the door into the receivers and fully seated. If this is how it is installed then you may need to replace the receivers for the unit. Read More...
Felicia September 23, 2014 for Model Number How to Replace Door Hinge #W10347466 I watched video and used it to replace hinges. Now the door closes but will not stay open now. The video doesn't address the issues of now not staying open.
1 Answer The door has to be opened to the full extension or the broil stop in order to stay open. Read More...
Felicia September 23, 2014 for Model Number How to Replace Door Hinge #W10347466 I've replaced the hinges on my whirlpool oven due to door not closing but now the door will not stay open suggestions?
1 Answer Hello Felicia. There is a video on the parts page for the hinges. http://www.appliancepartspros.com/whirlpool-door-hinge-w10347466-ap5325898.html Read More...
Chef June 06, 2014 for Model Number KEBC147 KBL03 Will this hinge fit in the door of a Kitchenaid Built-In Electric Convection Oven Model # KEBC147 KBL03 (serial number is XP4606959) bought in 2003? Thank You.
1 Answer Hello Chef! no, the door hinge kit W10347466 will not work on your appliance. According to your model you'll need hinges part numbers 9760569 and 9760570. Thanks! Read More...