Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Range Surface Burner Ignition Switch With Shield by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM12028992
Manufacturer Part Number: 12002792

Burner won't spark or ignite? This surface burner ignition switch triggers the spark module when you turn the knob. 45-minute DIY repair for ranges.

More
$102.32

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Range Surface Burner Ignition Switch With Shield (Part Number: OEM12028992)

1 Answer

Barry, the ignition switch 12002792 would have each switch block just pulled off one at a time and replace the one pulled with the corresponding switch block from the new harness.

Read More...

1 Answer

David,
With a multimeter check at the L1 to N at the spark module with the surface burner switches on. You should have 120vac at that point with any one of the switches in the on position. If you have the 120vac then it is the module or the wiring to the ignitors. If you don't have the 120vac the issue is the wiring to and /or through the surface burner wiring or switches.

Read More...

1 Answer

Michael, there is an ignition switch that fits around each valve stem that needs to be replaced, part number is [12002791]

Read More...

1 Answer

Judy, remove power to the range, remove the grates burners and knobs. Carefully raise the top panel and check the ignition switches for burn marks and arc marks from the switch shorting out from the water spillage. If all's OK replace the spark module on the back of the range.

Read More...

1 Answer

Hello Steve. No, there is no other way to replace it other than the way it is posted. Sorry.

Read More...

1 Answer

Hello Steve. Maintop Removal
1. Disconnect power before servicing.
2. Remove surface burner control knobs by grasping
knob and raising knob straight upward.
3. Remove screws securing infinite switch bracket to
maintop.
4. Remove screws securing burner assemblies to
maintop.
5. Remove screws securing maintop to chassis.
Screws are located in the front left and right corners
with the upper oven door open.
6. Remove screws securing ground strap to chassis.
7. Raise and remove maintop from unit.
8. Reverse procedures to reassemble.

Read More...

1 Answer

Hello Melissa,
Although this is not a good picture at all, this 12002792 is a five switch harness. I looked it up to verify it for you.

Read More...

1 Answer

Howard, Yes, the 12002792 / 12002792 Ignition Switch/ w shield will have the five(5) switches. "Switch Assy. Ignitor Switches That Mount On Surface Valve. Comes With All Five Switches W/Harness." You should be fine with the ignition switch assembly.

Read More...

1 Answer

Hello Bob. To gain access to the ignitor switches on this model, it looks like you will need to remove the screws by the valve stems (under the knobs) to enable you to raise the top without raising the manifold. The valves mount on the manifold between the gas manifold and the main top. Hope this was helpful!

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google