Clive August 08, 2021 for Model Number PER5510BAW The oven control panel has shifted slightly on the left side. The panel lights up only on the time function at about 11:43 on some days. I have not tried the oven since this has occurred but the stove top is still working. The oven light still works. Do you think the circuit board needs to be replaced or just fixed properly to the housing
1 Answer Clive, this could be a broken mounting bracket on the oven control WP5701M680-60 or a broken mounting post on the panel 2601D840-81. Unfortunately, both parts have been discontinued by the manufacturer and are no longer available. Read More...
Clive August 07, 2021 for Model Number Maytag Performa Advance Cooking Range The oven control panel has shifted slightly on the left side. The panel lights up only on the time function at about 11:43 on some days. I have not tried the oven since this has occurred but the stove top is still working. Do you think the circuit board needs to be replaced or just fixed properly to the housing?
1 Answer Clive, if the model number of your appliance could be provided in a new question, this will allow the most accurate information to be presented. Read More...
Karl June 17, 2015 for Model Number MER5530BAW My control panel lower button has failed. The part # for the controller is 5701M679-60, The knockoff replacements look horrid relative to our white range. Found a used 5701M680-60 on EBAY will it work?
James T December 27, 2014 for Model Number PER5510BAW Maytag electric Oven bake coil is coming on by itself at full heat, the control panel is showing no signs of life ( no clock or feed back when pressing buttons ) The only way to stop the oven is to switch the breaker. Control panel or should I look at something else?
1 Answer James, With the control being out and the units bake coming on by itself, this would be a faulty control board WP5701M680-60. Read More...
Jose N. December 19, 2014 My stove got the F1 code after we start using the oven, I checked the control unit and it's broken the circuit board. I just wanna be sure that it's just the control unit and it's not something else after I spend $220 on a new one....
1 Answer Jose', The F1 error code does indicate a problem with the control (relay energized during the time of day mode). If the printed circuit board is cracked or broken as you stated, you'll need to replace it, either way. But chances are good, you won't need anything else. Read More...
John December 14, 2013 for Model Number PER5710BAW why is the control panel lights keep flashing. the stove and oven work but all the lights flashes
1 Answer John, Your first check needs to be to the power supply (breakers and outlet). The check and make sure the connections on the back of the range at the terminal block ( where the power cord attaches) are not loose or damaged. "The display will flash when electrical poweris first supplied to the range or if there has been a power failure." If all's OK, you'll need to replace the ERC/Clock WP5701M680-60. Read More...
Richard July 06, 2013 for Model Number per5710baw My key pad was looked so I reset but now when I press bake/broil the display is off.
1 Answer Richard, If the display is not coming on the unit then you would need a new control board for the range. Read More...
Mo March 26, 2013 for Model Number PER5710BAW My oven lock light was also coming on after pressing the broil/bake pads. Also, I get the F9 code when I try to clean my oven. Upon trying to unlock the keypad (pressing stop time and cancel simultaneously), the panel shows an "OFF" message whenever I try to do anything now. What do I do?
1 Answer Hello Mo. Based on the code, the door lock assembly is bad on the unit and will need to be replaced on the unit. Read More...
Laura February 10, 2013 for Model Number maytag PER5710BAW Hello , While trying to turn on the stove it beeped and gave the F1 code and no sub numbers . Checked and The bottom heat element was broken. Ordered one and installed but still getting the F1 code. The Control board need to be replaced? Bought this stove back in 2005 , is this the life span of stoves these days? I will have to get a new one as there are burners that have quit working as well.
1 Answer Hello Laura, The F1 error code will indicate an error in the circuitry. Test the oven sensor first to make sure that it is 1090 ohms. If within 10 percent then it is good. If not then it is bad. If sensor is good at room temp then you would want to replace control board. WP5701M680-60 Read More...
1 Answer Hello KB. If the code is f1-9 then yes, the erc WP5701M680-60 will repair the problem with the unit. Hope this helps. Read More...