Frank A March 10, 2015 for Model Number whirlpool rb120pxk-0 wall oven In attempting to change a burned out lamp bulb I shorted out the lamp holder; forgot to turn off breaker; tip burned off as well as the electrical connector. Do you have the holder in stock? Frank
1 Answer Frank, Unfortunately the light socket for your unit has been discontinued by the manufacturer with no suitable replacement. The part number is 660556. Read More...
Patrick January 27, 2015 for Model Number KERC700LBS0 Kitchenaid Oven Oven bulb burned out. replacement bulb doesnt work but is good (tested separately). The bulb that burned out looks like it got hot as some of the the solder around the base of the bulb is melted. Pulled the back panel and no power on the wires going to the socket. I can hear a relay/click when I open the door or hit the light button on the panel. Is there a separate transformer on this, or other power test I can do to identify what has failed?
1 Answer Patrick, You can test the oven light at the control board from connector P1 pin number 4 to P1 pin 1 for 120 vac with the door open or the oven light switch turned on. If there is no power then the control board is faulty and would need to be replaced. If there is power then check the wiring from the control to the light socket. Read More...
Sdw January 22, 2015 The light went out in the freezer section of my two door/one drawer fridge...3.6w led...are they really that expensive!!!! Can I use another type bulb. Thanks for any help.
1 Answer SDW, we would need your model to determine the replacement parts for your model. Please obtain this information and repost for further assistance. Thanks. Read More...
Sylvia M January 15, 2015 for Model Number CWE4800ACB How do I get the light cover off it is a wall oven.
1 Answer Sylvia, This light cover would just screw off. You may have to get ahold of it with a grip type of rubber pad in order to get it off. Read More...
Orvie S. December 05, 2014 for Model Number w30400w How do I remove the light bulb so it can be replaced?
1 Answer Hello Orvie, The bulb cover unscrews to expose the bulb. It will tend to seize from the expansion and contraction of the materials from the operating temperatures in the bake compartment, so it may be necessary to use a rubber bottle opener for grip to get it unscrewed. Read More...
Rebecca October 07, 2014 for Model Number Admiral AT19N8 The light bulb was working fine, then died, so we suspected that it simply burned out. When we removed the bulb, it appeared burned out, purchased a standard 40 watt appliance bulb, with screw in threads, as pictured on this site. The new bulb doesn't work. So I will purchase another, as this is one I had on hand. My question, is if it still doesn't work, where else could the problem exist?
1 Answer Hello Rebecca. Make sure the light socket is not damaged. If it is good, then the door switch may be bad. Read More...
Kevin August 18, 2014 for Model Number ED5VHEXVQ01 The Water Filter Status Light was green and now it is not showing any color. How to I change this light bulb and what size bulb do I need?
1 Answer Hello Kevin. The indicator W10853646 is located in the control panel. You must drop it down to access and replace the light. Read More...
Mary August 03, 2014 for Model Number RTD1900DAE The light bulb in the refrigerator section flashed and the glass separated from the base. I don't think I can get the base unscrewed without removing the whole light fixture. I tried with needle nose pliers. No luck. How do I remove the fixture?
1 Answer Hello Mary, You will need to remove the screws that thread straight up towards the ceiling that retains the control cover. This will lower down to provide access to the light socket. Be very careful with the socket 61001772 since it is no longer available and no satisfactory substitution has been provided by the manufacturer. Read More...
Joseph June 24, 2014 for Model Number Whirlpool - GC3SHAXVY02 How can I remove the light shield to replace the bulb in this unit?
1 Answer Joseph, In the middle back part of the cove there is a round piece. you need to lift the round piece and pull toward the back of the unit in order to release from the housing. Read More...
Deo W. June 04, 2014 for Model Number KEBS177WBL-3 The recommended relacement bulb for this unit, listed in the users guide as No 41373175. The replacement bulb I got is much too small for the socket in the back of the oven, which seems to be a standard light bulb socket. . A replacement 40 W appliance bulb will not screw into the socket. It appears that the shoulder of the bulb prevents it from going deep enough to make electical contact, although if I hold the buld in the socket it will light, just won't screw in and stay. A regular bulb will stay and lights o.k. Is it possible that the receiver for the bulb has to be replaced, and if so, how can that be accomplished and where would it be gotten? The diameter of the heavy glass bulb cover is 2 1/4 inches where it screws into the back wall of the oven, on the upper left side. This is very perplexing. Any solution?
1 Answer Deo, according to the model number given the replacement bulb listed for your model is part number 8009. This is the only replacement the manufacturer offers for your model. Thanks. Read More...