Stephen October 24, 2016 for Model Number C970 600133 My self cleaning oven always stops working in the middle of cleaning cycle have changed reset module and thermostat
1 Answer Hello Stephen. The model number will have to be verified on the units I.D. tag since the one listed came up invalid. This will be necessary to look up and specific parts such as the one you requested. Thank you for your patience and understanding in this matter. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Marilyn August 26, 2016 for Model Number IC6 top and bottom freezer How do you change the light bulb in the freezer?
1 Answer Hello Marilyn, If the configuration you have is similar to the parts diagram under the part, you compress the light lens top to bottom to release the plastic tabs and unscrew the old bulb for replacement. If it is not the same as the parts diagram under the part you were viewing we will need the model number from the unit to give specific information on the unit in your home. Read More...
Wilson August 10, 2016 for Model Number CSX 2.4D How to replace light bulb in model CSX 2.4 D a 23.8 Cu FF.
1 Answer Hello Wilson. You will flex the cover and remove it from the unit. Then unscrew the old bulb and screw the new bulb into the socket. Read More...
Sharon B. April 17, 2016 for Model Number JSP342WKWW I have a model JSP42wKWW oven. I am replacing the bulb. It does not screw out but has tin enclosures around it. Do I Take a small wrench to remove this ring? Thanks
1 Answer Hello Sharon, The bulb should unscrew from the socket assembly WB8K5042. If you cannot remove the bulb and want to remove the socket you will have to remove the main back of the unit to access the socket. It is held in by metal tabs made on this assembly. Removing the wires to the light socket and depressing the tabs will allow you to remove the light socket from inside the bake compartment. Read More...
Bennett J March 26, 2016 for Model Number jbp23dr3ww How do I remove the protection wire that is over the bulb cover? What # appliance bulb do I buy?
1 Answer Bennett, The wire just pulls to one side to unhook and then slide off the other side and the part number for the bulb will be 40A15. Read More...
Tony B February 09, 2016 for Model Number 9825XUB Hi I was referred to you by Kyle from the chat department I have a Magic Chef Double Wall Oven. I changed the upper bulb with difficulty. I know I will have to replace the light unit in the near future. I looked up light assemble AP5691871 The video show how to replace light unit on a self standing stove. Is this the same light assembly? How is replacement made? Can I do this from inside the oven without taking the double oven out of the wall? If so, do I snap the clips the same way to take out the unit. Will wires in the back of over come through the hole so I can connect the new light assemble? Your help would be appreciated so that I might order and install the proper light assembly. I did replace the front glass on the upper oven a short time ago so I am familiar with working on unit so long as I don't have to take full wall oven out. Thank You
1 Answer Tony, The light assembly will come out from the inside but if possible would be best to remove the wall oven from installation in order to access the clips to depress to get the light assembly out. This is similar to the one in the video but may need not be exactly the same. The wires may not be long enough to come through. You could try like the video but may be necessary to remove the oven. Read More...
W. Sullivan January 21, 2016 My oven lite bulb (hotpoint stove) burned out.. I replaced it and it burned out in 3 days. bought a new one which also burned out in 3 or 4 days. I cleaned around the base with no rust or anything. Unit about ten years old. Any suggestions? Thanks.
1 Answer W. Sullivan, You will want to pull the unit out and access the light socket and check voltage to the socket to make sure that it is getting 120 vac to it. If the voltage is too high then you will need to replace the control board. If it has proper voltage then the socket would most likely be the issue. Read More...
Christi November 09, 2015 I ordered a replacement bulb for my Whirlpool oven. It is a universal part number 8009. However, the bulb socket has no lens cover, and to my knowledge never has. Does the bulb need protection, and that's why I'm reading about lens covers? Is some kind of covering over the bulb required? Thanks for any help.
1 Answer Hello Christi. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. Here is a link to help you locate it. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Jgw August 12, 2015 for Model Number MFI2269VEW1 Need a freezer light bulb for my Whirlpool frig for model # given. Can I use any typical 40 watt appliance bulb or do I need a specific bulb?