Rana September 04, 2015 for Model Number Whirlpool SM 8280869 Hello. I need to replace my agitator dogs and want the whole kit. Please advise the model number. Thank you.
1 Answer Hello Rana. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. Here is a link to help you locate it. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Rana August 31, 2015 for Model Number SM 8280869 Hello. The top part of my agitator is not agitating. I believe I need to replace the dogs. I'd even settle for a whole replacement kit. Please advise what model number the dogs are.
1 Answer Rana, The 80040 Agitator Dogs is the part number needed for the "dogs" only. Don't forget to put a dab of grease under each dog when you mount them to the cam. Read More...
Paul R August 17, 2015 for Model Number wtw5600sq0 I have part # 3951608, thrust washer, it says to set it in the slots on top of the agitator, but thre are no slots, there are Raised tabs on top. it dosen't appear it engages in any slots on either side. Please advise if I just set it on top of the agitator then put agitator back in.
1 Answer Paul, The thrust washer goes in between the upper and lower agitator. This would just sit on the top of the lower agitator base and the agitator top pushes down on to it. Read More...
Tiffany August 14, 2015 My agitator basically fell off during the rinse cycle. I have a Roper. I took the screw off and "redid" it but the piece pulls off again.
1 Answer Hello Tiffany, This sounds like the hole in the agitator has wallowed out. This will require the replacement of the agitator at least in part, dependent on the model. For more information, please re-post in a new thread and please remember to include the model number from your units' I.D. tag. Thank you for your patience and understanding in this matter. Read More...
Paul R August 09, 2015 for Model Number wtw5600sq0 I'm replacing the Cam, Driven assembly and it calls for applying grease, I don't have what's specified, what can be used in it's place?
Richard July 12, 2015 Agitator keeps coming up when water is added to washer agitator won't stay in place
1 Answer Hello Richard. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. Here is a link to help you locate it. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Guy June 04, 2015 for Model Number KAWS850LQ0 Hello. My Kitchenaid superba KAWS850LQ0 washer will not agitate or spin. It will fill and drain fine, the cycle knob moves thru the correct setting, but will not agitate or spin. The agitator only turns clockwise, and after reading some other postings, i fear the agitator dogs may be stuck...??? The washer does fill with the right temp water and does drain properly, but makes a noise emanating from rear of machine when it should be agitating and/or spinning. Please advise me on what may be causing these problems and if it is possible to fix them. If i can fix this issue by replacing parts myself, please let me know which parts may solve the agitator and spin problems. Thank you very much. -Guy
1 Answer Hello Guy. You can check the dogs in the unit. However, the agitator in this model only goes in one direction. As for the noise, it may be that the transmission is bad and will need to be replaced on the unit. Read More...
Patricia March 25, 2015 for Model Number WTW4910XQO My washer will wash and than stop and after a while will drain all the water and stop. I can't get it to do anything else. I have change the dogs, but still doesnt do nothing else.
1 Answer Patricia, You will want to get the tech sheet from the control panel of the washer and put it into the diagnostic mode. You will want to check to see if there are any stored error codes. The most likely cause for the unit not spinning would be a bad actuator but running diagnostic will help to determine what the cause is. Read More...
1 Answer Hello Pat. If the motor runs, but the agitator does not move, you will need to replace the cam kit. If the motor does not run, you will need to check the lid switch. Read More...
Paul September 23, 2014 for Model Number LXR9245EQ1 I need parts for the top agitator. Do I need the short,medium or long cam? Which grease would I need? Is the thrust washer item 22 in diagrams included in the agitator repair kit item 9? Do I need grease for the thrust washer? Also how old is this machine? Thanks.
1 Answer Hello Paul! Your model uses the medium cam kit part number 285811. Yes, the kit includes the thrust bearing washer. Yes, you'll need to use a dab of grease for the washer. We'll need your appliance serial number to verify the age of the unit. Thanks. Read More...