Levi September 09, 2014 for Model Number kenmore 110 top load I have grease on our clothes every once and awhile, I took the agitator off and there is grease everywhere. I am assuming its a seal?
1 Answer Hello Levi. It sounds like the transmission is bad and will need to be replaced on the unit. Read More...
John R. August 26, 2014 for Model Number LLR8233DZ0 My LLR8233DZ0 washer has a serial number CE30001869 (mid 1990s manufacture date). The agitator mover is almost free wheeling. The lower agitator seems to still be secure on the agitator shaft. Can you advise on which cam (short, medium, long) repair kit is appropriate for my model and serial number? Thank you.
Bill August 19, 2014 for Model Number MVWC200XW2 Washer does not spin. I already replaced lid switch. What is the problem? Thanks
1 Answer Hello Bill. You need to check the actuator switch and the belt and pulley on the unit. If all of that is good, then the transmission will need to be replaced. Read More...
David A. July 26, 2014 for Model Number LSQ8243HQ0 I want to buy the agitator cam repair kit #285811, but I'm not sure it will work for my model # lsq8243hq0. If it doesn't, do you have one that will. Thanks! Dave
1 Answer Hello David! No, the medium cam agitator repair kit is not listed as compatible with your appliance. Your model uses the short cam agitator repair kit part number 285809. Thanks! Read More...
Charlie B. July 19, 2014 for Model Number 110 - 9229100 Will the Whirlpool 285811 Agitator Repair Kit work on the Kenmore Washer model 110.9229100 heavy duty 80 series?
Gloria July 17, 2014 for Model Number wtw6200vwo Washed a thin sheer piece of fabric. at the end of cycle part of the fabric is stuck under the agitator. what size socket wrench do I use? Metric or standard? Thank you.
1 Answer Gloria, Using a ratchet with a 7/16? socket and a 12? extension, remove the hex head bolt from the agitator, then lift the top half of the agitator out of the washer. Read More...
John June 27, 2014 for Model Number 11020702990 When the washer goes to spin at first it sounds like clutch slipping. It will finally spinup and quiet down all else ok. What do I need Please.
1 Answer John, The most common thing that would cause the issue would be a bad clutch assembly. Read More...
Steve June 24, 2014 for Model Number kaws750lq2 I have a kaws750lq2, Kitchenaid top loader washing machine. It makes a sound like plastic gears slipping when in the more intense agitation settings. With just water there is no noise, in the delicate setting there is very little noise and the noise intensifies as the setting goes toward cotton setting. I replaced the agitator dogs with no change. It seems as though there is some slop between the dog assembly and the top agitator. The teeth on the inside of the agitator seem intact. I can hold the top agitator still while agitating which makes the same noise. This leads me to think that the problem is in the upper agitator assembly. Should I replace the top agitator and the dog assembly? Is there something that I am missing? What would you suggest?
1 Answer Steve, Open the lid and grasp the agitator top, turn it counterclockwise, the auger should move freely and make a clicking noise. When you turn the auger clockwise, the auger should lock and not move. If you can move it in both directions then install the cam kit 285811 and auger 3950581 If all goes as described, you'll need to remove the complete agitator and check the splines in the center of the bottom of the agitator and the agitator shaft for plastic shavings or chips, indicating the lower agitator 3950580 has "stripped out" on the shaft and is making the noise. Read More...
1 Answer Hello Gary. It sounds like the timer WP8541942 is bad and will need to be replaced on the unit. Read More...
Polly June 03, 2014 for Model Number LSC8244DZO Washer will not agitate or spin but the water drains out. What's the problem?
1 Answer Hello Polly. It sounds like you need to check the motor coupling 285753A on the unit. If broke, or bad, it will cause the issue you are having. Read More...