J Wald August 21, 2013 for Model Number Roper RAS8245EQ1 I am going to order the Medium Cam Agitator repair kit for my washer. While I'm at it, I see that the washer tub is leaning to the left all the time. I can only assume that a keeper, or spring, has weakened. I can pull it to center, but it gradually slips back to the left. Any ideas why it is leaning? Thanks.
1 Answer Hello J Wald. It sounds like you need to order and replace the suspension spring WPW10250667 on the unit. Read More...
1 Answer Dontime0118, It sounds like the agitator cam is bad or a bolt is loose if equipped in the agitator. Read More...
Joe R. August 05, 2013 for Model Number LA5600XSW1 What are the dimensions of a short cam, medium cam and long cam? Don't know which one I have. Thanks.
John July 25, 2013 for Model Number model # 417.97822701 I have a Kenmore piggy/ back washer and dryer heavy duty extra large capacity piggy back washer and dryer my Agitator is not working the belt is working when washing but the Agitator is not working .but when it spins at the last cycle the pump works thank you for your help
1 Answer Hello John. Make sure the hub is not stripped out 134418700. If not, then you will need to replace the transmission. Read More...
Asa M. July 02, 2013 for Model Number wtw5500xw0 Lid Lock Display Flashes But Sometimes It's Unlocked When Flashing And Sometimes Not. I NoITiced The Washer Was still Filling With The Lid Open. It Isn' t Agitating Or Spinning. However, It sounds Like It's Working. There Is A Burning Smell And An Extremely Loud Noise On The Final Spin. What Could Be Wrong?
1 Answer Asa, The intermittent issues with the lid lock is most likely due to a faulty actuator WPW10006355. There are internal sensors and switches, that communicate with the control board and "tell" the control to lock the lid and operate the motor. If the switch is malfunctioning, it could cause the cam W10721967 in the "splotch to deform and make noise and "drag" and cause the odor. Both of these components are located on the bottom of the gear case, so you'll need to lay the washer on it's back or raise the front of the washer enough to get under it. Read More...
Henry C June 27, 2013 for Model Number LAT9406AAE My Maytag Washer Machine won´t spinning but the water pump work because take the water out, also the agitator work because in the cycle it work too, so what is your suggestion part to be checked and replaced Thanks
1 Answer Henry, You will want to check to make sure that the belt is not broken or slipping. Check to make sure that there is no clothing stuck between the tubs. Check the spin bearing to make sure that it is not seized. Check the water level switch to ensure that it is reading that the drum is empty. Check the speed selector switch. Check the motor protector switch to make sure that it is good. Read More...
Eric June 12, 2013 for Model Number wtw5300sqo On the grease that you want us to use when putting agitator cam back together [white gease] can I use something that I might have around the house??? thanks eric
1 Answer Hello Eric. No, they do not recommend using anything but agitator grease on the unit. Read More...
Mary June 07, 2013 for Model Number wtw5100vq0 what if the bottom agitator is not working or moving looks as if the top is ok bottom is not agitating but machine will spin out
1 Answer Mary, You will want to pull the agitator off and check the splines on the drive block to make sure that it is not damaged. Read More...
Bob W April 17, 2013 for Model Number LSQ9544KQ0 All steps to remove the agitator are done, however I can't separate the upper and lower portion by pulling it up as suggested. If it has tabs to lock it in, how do I separate them to change the dogs etc ? Whirlpool Washer.
1 Answer Hello Bob. Some of these can be hard to separate. You will need to stand on the base of the agitator and jerk upward to remove the two. This may require some force to do. Read More...
Ron February 11, 2013 for Model Number LSR8233E Need help diagnosing whirlpool washer model LSR8233E. Noise produced during spin cycle. Sound persists even with agitator removed. Please see video http://youtu.be/sGO0N086eIQ. I plan to purchase parts from you if you can help.
1 Answer Hello Ron. After listening to the noise of the washer, I would advise to remove the motor, transmission, and drive tub and look for damage. If none is found, then it would appear to be the transmission in the unit. Read More...