Marco July 25, 2023 for Model Number KSGG700EBS1 Hello, when I use the oven it turns on for a minute then automatically shuts off and throws a F9E0 error code. It also throws error code when not using. the top burners work fine its just the oven I can't use because of the error code supposedly its a misswire but all wires look fine is this a control board problem if so is it the one above? Please help. KSGG700EBS1.
1 Answer Hello Marco, that code is for a miswired power supply for an electric range, (240v), since this model is a gas range (120v), the control board thinks it is in an electric range, which would indicate a failure in the control board, part W11034208. Read More...
Bob June 06, 2022 for Model Number WEG730H0DS0 nothing electrical works. Not the igniter.ovev light or display board.Gas still floes and we can light with a match. Is it module AP5999387 ?
1 Answer Hello Bob, the cooktop spark ignition is a separate circuit from the oven control board, since neither is working, likely there is no power going to the stove from the outlet, the line cord is damaged, or the main wire harness located inside the rear of the cabinet has had a problem. Read More...
Greg March 04, 2021 for Model Number KSGG700ESS0 The oven is not heating but you can smell gas inside the oven when it is turned on. All the top burners lite and work. I guessed that the oven igniter or spark module must be the problem. I see that this range has 2 spark modules, which one works the oven? I assume the 2+0 is for the oven. Is there anything else I should check out?
1 Answer Hello Greg, the spark board W10860916 is only for the oven,(bake/broil burners), the bake ignitor is part WPW10324262, Start by using a multimeter and check both gas safety coils (pressure regulator/gas valve assembly for about 215 ohms for each coil, if not reading correctly it will need to be replaced, if ok access the bake burner ignitor, push in and hold in the oven door switch, set to bake 350 deg, and check there is a strong spark off the bake burner ignitor, it should spark 2-3 x while opening the gas valve momentarily, if the burner does not light, it will pause 30 sec and retry, the 3rd time the spark board will stop trying. Read More...
Bob June 10, 2020 for Model Number WEG750H0HZ0 The oven will not heat in the bake. the broiler comes on when commanded. I don't hear the click from the spark igniter or the gas solenoid on the gas valve in bake command but I hear it in broil command. I replaced the spark igniter and the spark module - could it be the circuit board? I witnessed the spark from the bake igniter when I commanded the broiler to come on, but nothing during the bake command, also, my voltage to both igniters is 29 volts - this was enough to ignite the broiler and create a spark from the bake igniter.
1 Answer Bob, It would be recommended to set the unit to bake and test at the control board from bake to neutral and see if there is 120 vac coming off of it. If there is not then the control board is faulty and will need to be replaced. The part number for the board is W11205353. Read More...
Betty May 16, 2020 for Model Number KSGG700EBS1 The convection burner in the oven stays on and never goes off unless power cord gets unplugged. Is this a common problem on this gas range?
1 Answer Hello, Betty. No, this problem is not common and because the convection burner is not gas, the cause of the problem is not connected to the spark module. Very likely the convection element relay, which is a part of the range control board, is shorted. The solution is replacing the range control panel w11091882 Read More...
Martin March 04, 2019 for Model Number MGS8800FZ0 Display doesn't come on when I plug the range in. Oven functions seem to work via touchscreen, but you can't see what it's doing and what temp to adjust. Light switch works as well.