Ed December 19, 2012 for Model Number gge350lwb00 Both ovens were not keeping constant temp. Checked with a probe and they were off by 50 or 60 degrees both ways. Unplugged and replugged power...code that came up before the time came back on was: 3.0. I installed the sensors for both ovens. It did help the wild fluctuations of temperature in the ovens. But the fault reading (3.0) still comes up for a brief time when I unplug and replug the power. What does that 3.0 mean?
1 Answer Hello Ed, This 3.0 that comes up would just be the software version of your control board and is normal for this to come on during power up. Read More...
Jim November 27, 2012 for Model Number MER6770AAW I have a Maytag Gemini and it heats up to whatever temp I want and after 30 or so minutes it gives me and error code F3. I can shut it off and it will restart but after a while it gives me an F3. Is this the oven sensor and should I replace both. Both ovens act up. Are they wired in series.
1 Answer Hello Jim, You can test your oven sensor 12001656 to see if they are bad. At room temperature they should ohm out at 1100. If they are not then they need to be replaced. Check both sensors. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Allen S. November 05, 2012 for Model Number Kenmore 9113022190 I recently installed the 8053344 sensor in my Kenmore model 9113022190. It seems the sensor only works on the higher temps (over 400 degrees.). If it is set on 350, it quickly goes up to 350 and then shuts off and I can't get it to go on again unless I raise it to over 400. Any suggestions short of a new oven?
1 Answer Hello Allen, You should test the oven sensor WB23X5340 to ensure that it is not bad. Check the wiring as well to make sure you have good connections. The sensor should ohm at 1100 at room temperature and 1650 at 350. If the oven sensor is showing good then you would need to replace control board WB27T10327. Read More...
Allen S November 05, 2012 for Model Number Kenmore 9113022190 Oven I bought the temp sensor recommended and the oven is still not working right? Are all temp sendors non-polarized? Whatever temp you set it on the temp indicator quickly moves to that temp and when its there the oven shuts off. It will stay cycle off and on at the higher temps like 425 and up but not at 350.
1 Answer Hello Allen. Yes, if the sensor is new, you will need to order and replace the clock control board WB27T10327 on the unit. Read More...
Angelo November 01, 2012 for Model Number MERH752CAS Does this item include the wires that connect directly to the control board?
1 Answer Hello Angelo. No, it includes the wires to connect it to the connector in the wiring harness. Read More...
Kbf October 26, 2012 for Model Number matag 6770aaw Error code f1-8 comes up when trying to use the oven. Top works fine. Any ideas of what might be wrong?
1 Answer Hello KBF, The error F1-8 indicates runaway temperature. What you want to do is check your oven sensors 12001656 to make sure that they are good. With a multi-meter ohms the sensors out. They should ohm out at about 1050 ohms at room temperature. If the sensors show good then you would need to replace the control 12001661. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Sanchez October 19, 2012 for Model Number Kenmore 9113022190 I have a Kenmore 24" cabinet mounted oven. I had Sears come out and and told me the sensor was bad but, that the part was no longer avaialble. This unit looks similar, but would it work in Kenmore.
1 Answer Hello Sanchez. Based on the model number you provided, WP8053344 is the correct sensor. Read More...
Oscar T October 10, 2012 for Model Number MER5755QAW Hello, Our oven only heats up to 200 degrees after setting the temperature at 350. I need to know if this is an element issue or an oven temperature sensor issue. I would like to order the correct part first time around. Please advice. OT
1 Answer Hello Oscar. You need to test the element and see if it is good in the unit. It should read closed for continuity. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Foster2906 September 13, 2012 for Model Number mer5755qab How to test my oven temp sensor /I replace my control panel a year ago now its over heating again.
1 Answer Hello Foster2906. The sensor 12001656 should read 1100 ohms at room temp and 1650 ohms at 350°. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Layle H. September 13, 2012 for Model Number CHE9830BCE An F-3 fault code comes on when the oven is in use. Is that a temperature sensor problem or could it be more serious to require some other parts? I'm 70 miles from any repairman. Is this something I should try to fix or is it worth the risk? It doesn't seem to hard to do if instructions come with parts.
1 Answer Hello Layle, The F-3 code is the failure code for the temperature sensor. This means that the control board isn't properly receiving the information from the sensor. This can be a bad connection, a shorted or broken harness, a bad sensor, or the receiving circuit in the board has failed. The most likely cause is the sensor so when you test it with a resistance meter, it should read about 1100O at 70°F. Be sure to tap on the sensor during the test so if it is intermittent, it will show up. The sensor isn't hard to change. Two screws and pull the connector through the rear wall and unplug it and it's in your hand. The most important part is insuring the connector goes all the way through both layers of metal so it isn't in the insulation section between the two. This would cause the connector to melt from normal operation and causes the sensor circuit to fail prematurely. Read More...