Cat September 07, 2012 for Model Number JDR8895AAS Hello, Our bottom oven is basically not preheating. I'll set the temp to 350* and an hour later it's still at 195* We get no messages or error codes. We just replaced the clock switch unit for other issues that did get resolved but this had no effect on the lower oven. I'm guessing it's this temp sensor and would like to order it right away but I would like to be sure and also know if we should order any other parts to make this heat up again? Also, while I'm here... In the past it seems that the whole unit go haywire when we use both the top and bottom ovens. The clock goes blank, starts to blink and a little red dot starts blinking. But we get no error messages. Both ovens turn off and we have to wait a bit before using either one again. Any suggestions? Thank you for your time.
1 Answer Cat, based on your post, the most likely issue is the lower oven bake element WP7406P428-60, check and make sure there are no brokrn or cracked areas on the element and no loose connections. Re check and make sure you did not cross any wires at the new control, when you replaced it. That could be part of the issue with the control. If all's OK and the issue still remains, then replace the control again. Read More...
Scader September 06, 2012 for Model Number SVE47600B When I replaced the sensor wires it was impossible to get the adapter through the hole in the batting, so it sat between the batting and the oven. Is the adapter supposed to be on the outside or the inside of the batting? I believe the service technician failed to realize this and therefore the adapter was not protected by the batting and melted. In response to your previous answer, we haven't used the self-cleaning option on the oven since the new sensor was installed, so it melted from much lower temperatures; at max 420 degrees F. Thanks for your help.
1 Answer Hello Scader. The connector should go through the hole to the back of the unit. If the back access panel is removed, you should see the connector on the unit. Read More...
Scader September 05, 2012 for Model Number SVE47600B About two months ago a service company installed a new sensor. It was working fine until lately we get repeated F5 error codes. Typically, if we let the oven rest for a few hours it works fine afterwards. According to the wire diagram located on the oven, this is oven caused by a loose connection of the sensor. I figured the service company failed to properly seat the new sensor. Thankfully, the sensor removes from inside the oven as the oven itself it set into the counter top. I removed the "new" sensor and discovered that the plastic connection between the sensor and the adapter is brown and a even slightly melted. The connector to from the adapter to the rear wire looks fine. I don't know how this is possible as all those components are pushed into the back of the oven behind the sensor. Any thoughts? I'm concerned that if I buy a new sensor that it will just melt like the previous.
1 Answer Hello Scader. This usually happens during the self cleaning cycles and ifs from the extreme heat. There is nothing that can be done, other than not using the self cleaning cycles in the oven. If the sensor is bad, you will need to order and replace the sensor 12001656 in the unit. Read More...
Laura B August 19, 2012 for Model Number JGS885oadw I am getting a F9-2 code. It used to shut itself off after being on at a high temp for anything over 40 minutes. I could just turn off and let cool and it would work. Now it won't even turn on.
1 Answer Hello Laura. You need to check the temperature sensor 12001656 in the oven and make sure it is good. It should read around 1100 ohms at room temp and 1650 ohms at 350°. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Kathy August 16, 2012 for Model Number CRE9400CCE I went to use the oven and F-2 came up kept beeping. When you push bake or broil, no temperatures will come up. I turned the breaker off and on, then code F-3 comes up and beeps. Is the problem the oven sensor?
1 Answer Hello Kathy, You are right on the money. The temperature sensor 12001656 has failed or lost electrical continuity to the control board. Read More...
Fred Y August 06, 2012 for Model Number w2780b Purchased the sensor but I am still having the same issue. When I want to use convection oven . Set preheat to high temp and then it starts the fan motor running and humming and temp gauge drops to 140. Then it just shuts down. Please advise
1 Answer Hello Fred, Based on the information you provided, it sounds like the relay board WPY04100260 is bad and will need to be replaced in the unit. Read More...
Shelly July 11, 2012 for Model Number Fce30500w My oven quit working. The broiler works, but the oven barely heats up. Takes 40 minutes to get to 200 degrees. I replaced the bake element but it still doesn't work. Do I need to replace the long oven sensor? If not, what else could it be?
1 Answer Hello Shelly. Test and make sure there is 240 volts coming to the unit. Also, make sure the high limit 7403P160-60 reads closed on the unit. If this is good, you will need to look for a wiring issue between the terminal block and the element. Make sure the clock is sending 120 volts to the element as well. If not, replace the clock 12001603 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Sam April 30, 2012 for Model Number bnew3h9tz My NORGE electric stove have this, I set the temperature at 400 the stove and elements working fine but the temperature never going up to 400 going only up to 250 even when the oven getting cooler. But its never displays an F1or F2 error code.
1 Answer Hello Sam. You will need to test the bake element WPY04000041 and make sure it is good in the unit. It should read closed for continuity. If it is bad, the oven will not heat properly and would never go above 250°. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Fred A April 30, 2012 for Model Number MER5755QAQ Our range does the following: a) you set the temperature and start. b} Half the time it goes to temperature and half the time it seems to ignore the set temperature and just gets warm.We have unplug it and restarted and this seems to help for a while.Is this a sensor issue or something else?
1 Answer Fred, If you don't get an F2 or F3 error code, start by replacing the oven temp. sensor 12001656 especially if the issue started after a self clean cycle. Thanks and Good Luck Read More...
Ken April 02, 2012 for Model Number Maytag MER5570 After using the self-cleaning feature the oven will not unlock. I tried shutting off the power, but no luck. It always displays an F1 error code. After reading some of the other questions it appears the F1 indicates the temp sensor / probe. But then I read that you suggested unlocking the door with a coat hanger inserted from the left side. Would this serve to open the door and then keep the door unlocked so that we could use the oven normally?
1 Answer Hello Ken, The F-1 code is actually pointing to the control WP5701M556-60 as the problem. This part number has a black face. If yours is a different color, look it up using the last 3 letters of your model number and it should show a control with the correct color touch pad. Forcing the door open will not correct the issue as the locking mechanism will then prevent the door from closing all of the way. Read More...