Bob February 29, 2012 I have a Coin operated Whirlpool Washing Mach. I am not sure of the model number right now but I will check on that. The Mach works goes through all its cycles except it will not stop spinning when it is done unless I unplug it. Could you tell me what the problem might be I am wondering if it is either the Control panel or timer tks.
1 Answer Hello Bob. If the unit is getting stuck in the spin cycle, then the timer is bad and will need to be replaced in the unit. Hope this helps. Read More...
Sandy February 16, 2012 for Model Number AWM9150 I have a Whirlpool washing machine, model number AWM9150, and I need to replace the upper electronic control board (481241470006). Would you happen to know where I can purchase this? I'm having a lot of trouble finding it anywhere!
1 Answer Sandy, the model number given is an international model and we do not have any information regarding international models. You may want to contact Whirlpool directly to see who may carry this part. Sorry about that! Read More...
Cecil January 31, 2012 for Model Number LXR7144EQ0 I recently changed the motor coupling and put my whilrpool washer back together. The washer spins now but as the water fills up it seems to not stop unless I shut it off manually and turn the knob on the control button. Is the timer off now? It worked before I did the motor coupling.
1 Answer Hello Cecil! Try running the washer again. If you unplug it and the water continues to flow the water valve 285805 needs to be replaced. If it stops running, check the water pressure hose to make sure it has not kinked or clogged and if it is ok, replace the pressure switch W10852420. Hope this helps, thanks! Read More...
Rod Q October 29, 2011 for Model Number ghw9100wl Whirlpool duet front load washer, Control locked light stays light, have unplugged it for overnight, have held cancel button in for over a minute nothing seem to reset it?
1 Answer Hello Rod. If the control lock light stays on, and does not clear out or reset, you will need to replace the user interface in the unit. Hope this helps. Read More...
John October 21, 2011 I HAVE A WHIRLPOOL WASHER AND THE ADD GARMANT LIGHT STAYS ON WHILE THE WASH LIGHT COMES ON AND WASHER IS WASHING FOR 10 MIN THEN THE ADD GARMENT LIGHT FINALLY GOES OFF. AND F22 HAS BEEN COMING UP ON THERE AT TIMES. WHAT PART DO I NEED TO FIX IT.
1 Answer John, The F22 error code is usually an indication of a switch assembly failure, That would also explain the "Add Garment" light being on. Before you replace the switch assembly, check the loading door and door strike for proper alignment to the front panel door opening. You'll need to supply us with a model number, if you need assistance with a part number. Thanks and Good Luck Read More...
Jim N. September 24, 2011 for Model Number GSL9365EZ2 The washer goes through all cycles okay, but does not drain the wash water, if switched to spin mode the water drains. If put on extra rinse cycle the washer works okay, it rinses and drains. But does not drain on other cycles. Could this be a problem with the control switch? Do you carry the switch?
1 Answer Hi Jim. The timer is part # WP3953548. This should take care of it if you simply change the cycle's and all works then. Thank you. Read More...
Leelamoni July 09, 2011 for Model Number whirlpool alpha fully automatic-metallic innerside Even new clothes are torn or damaged in the washer. Can I exchange it for a non-metallic (fibre body) semi automatic machine ? If so,wahat are the concesion for it.
1 Answer Leelamoni, I'm not positively sure I understand your Question, But if you wish to exchange your washing machine for a different model or make, you will need to discuss that with the dealer you purchased the machine from. However, most damaged clothes complaints are due to improper loading and chemical usage, you may want to review and follow the use and care manual that came with the washing machine.Thanks and Good Luck. Read More...
Lakshmi June 10, 2011 for Model Number whirlpool alpha We have whirlpool alpha washing machine, but it is not working since 1 month. When call mechanic he said power board is problem. This part not available now. It is old model he said. We require 1 unit whirlpool alpha power board now. What can we do? Please answer our question.
Alan K. June 08, 2011 for Model Number cannot find it Old Maytag washer heavy duty 2 cycle. The mechanical dial that times the wash, rinse, and spin modes does not advance. If you manually turn it to each mode you can wash clothes. I'm thinking new dial. Am I correct? Can you just buy the dial or do you need an entire control panel? Also, where do you find the model number?
1 Answer Hello Alan! It sounds like you will need to change the timer assembly. We will need the model number to verify the part number. Here is a link to model/serial number locator to help verify the locations of model numbers, thanks! http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Ron May 30, 2011 for Model Number 034c My washer does everything but will not go into the spin cycle, would it be the control panel?
1 Answer Hello Ron! It would depend on your model number. What is your full model and serial number please? Thanks. Read More...