Rusty February 02, 2019 for Model Number WTW6800WW1 The "add a garment" light came on in the middle of filling for a load. It won't go off and it won't let us drain the tub.
1 Answer Rusty, what you will want to do is unplug the unit, let it sit for 15 minutes and then plug it back in. From there, you will want to enter it into a drain and spin to drain out the water. From there, you will want to check the voltages that are running between the user interface and the main control. Read More...
Joan November 07, 2012 for Model Number Whirlpool washer GHW9250MW2 Control panel MFG Number 8182088 is no longer available. What are our options? Is there a substitue that whould work?
1 Answer Hello Joan. Sorry, This part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Judith H September 09, 2012 for Model Number Samsung frontloader I have a samsung frontloader the heavy duty cycle will not fill with water, but every other cycle works fine. Just one cycle is not working. Is this something we can fix ourselves. Thank you
1 Answer Hello Judith. If the button is not working, replace the user interface. If there is no water comming in, test for power to the valve and look for clogged screens on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Donald September 02, 2012 My control panel seems to be out of time. When I start the machine, instead of it filling with water, it starts to agitate.
1 Answer Hello Donald, This sounds like a bad pressure switch to me. Again, I always list the part number but I cannot when there is no model number listed. You can repost with the model number or you can call in and one of our operators will be happy to assist you in getting the correct part number to correct your issue. Read More...
Steve W August 07, 2012 Kenmore 70 Series (clothes washer) Fill and wash cycles work. However washer does not drain in all setting and does not spin in any cycles. Can you advise
1 Answer Hello Steve. You will need to check and see if the lid switch is bad on the unit. If so,it will cause the issue you are having with the unit. Read More...
Guest August 05, 2012 Whirlpool duet. Plastic piece behind start switch. Button and plastic piece do not line up with electronic start sw. Where do I find one?
1 Answer Guest, sounds like you may need the user interface WP8182056. If you could repost your question and attach a model number, we can assist you more effectively and proper. Thanks Read More...
Carl August 03, 2012 for Model Number KAWS85OLQO I have a kitchenAid Superba washer and it over flows with water in the rince cycle.When I unplug it and reset the machine it seems to work ok .Any Suggestions? Thank You
1 Answer Hello Carl. Based on the information you provided, the pressure switch W10339326 is bad and will need to be replaced. Read More...
Bill May 01, 2012 for Model Number GHW9100LW2 The cycle control knob is not sleecting the proper cycle or cycle time. I believe this may have to do with a bad cycle control switch that the cycle control knob operates. Can I purchase the cycle control board seperate or do I need to by the entire control panel?
1 Answer Hello Bill. Yes, based on the information you provided, it sounds like the user interface WP8181905 is bad and will need to be replaced. Read More...
1 Answer Hello Normand. Sorry, but we do not sell parts for Splendide unit at this time. Thank you. Read More...
Jomes March 04, 2012 for Model Number mtw6600tq0 I'm getting a F1 code on my maytag bravos. If I push start three times, it will start the wash.
1 Answer Hello Jomes. F1 code is a bad control module. Based on the information you provided, the control module WPW10189966 is bad and will need to be replaced. Hope this helps. Read More...