Heidi January 18, 2017 for Model Number MAH5500BWW I have a model number MAH5500BWW and serial number A9291720EC. I am looking for the pressure switch. Three come up with the schematic and I am not clear witch pressure switch is for this serial number. Thank you
1 Answer Hello Heidi, You will need to order WP22003728 for the model and serial provided. Read More...
Jovan V March 18, 2016 for Model Number MAH5500BWW What does the pressure switch do? I recently had my drain pump motor replaced (just pump motor not assembly) because impeller was broken. Worked about 4-5 weeks, now my washer does not drain again. What could it be??? Does it make a difference by just putting pump motor on drain pump assembly instead of getting a whole motor and assembly as replacement unit??
1 Answer Jovan, The pressure switch is a water level sensor and would not cause the unit to not drain. Not draining would be caused by a clog in the drain system, bad pump or a bad control board. The pump that you will want to use on this unit would be WP25001052. Read More...
Curious G. December 14, 2015 for Model Number MAH5500BWW The pump went bad (broken Impeller) and when I had stripped it down to find the problem, the dry side of pump was full of calcium. I also noticed water sloshing in the switch. Since we have a lot of calcium in our water, I decided to disassemble to see if could clean it and if it was salvageable (it was working before the pump went bad, I think). However I unscrewed the spring tension screws thinking this would allow me to disassemble the switch (didn't touch the small adjusting screws) but now I'm thinking the larger torx head screws that I loosened on top of the springs are part (if not all) of the pressure adjustment. Thanks
1 Answer Hello Curious, If you opened the pressure switch, it will require replacement to make sure the unit does not flood the home. Read More...
Leonidas May 27, 2015 for Model Number MAH5500BWW Serial number: B2051486ET Model: MAH5500BWW What would the part number for the appropriate pressure switch according to my model and serial #? Thank you
Tom January 08, 2015 for Model Number MAH6500AWW Ser# 34535652en which press switch is correct? Please and thanks.
1 Answer Tom, based on the model and serial number given the replacement pressure switch is part number 12001891. Thanks. Read More...
Ellen July 14, 2013 for Model Number MAH5500BWW Washer spins but will not drain, instead meakes a grinding noise. Drain hose is clear. Should I replace the pump, pressure switch, or both? Which pressure switch, there are three? SN is 10761142YY, style Y7909216. Thanks.
1 Answer Ellen, You would want to pull the pump and check to make sure that there is nothing clogged in the pump. If the pump is clear then replace the pump assembly. Read More...
Tony June 09, 2011 for Model Number mah6500aww I am getting an FL fault on the front panel. Can't find out why.
1 Answer Hello Tony! A FL failure code indiactes the washer failed to lock the door. Close the door tightly and restart the cycle. If the problem persists replace the door latch WP22003593. Thanks! Read More...
1 Answer Connie, this part detects the amount of water that has entered into the machine and sends a signal to the water valve allowing it to shut off when the water level selected has been reached. Hope this helps! Read More...
Ronald February 18, 2011 My Maytag Neptunr washer Mod: MAH5500BWQ will not finish the spin cycle unless I lay the hose close to flat to the ground. I replaced the pump and the problem is still the same. What does the Pressure switch do that attaches to the pump. My door locks and the light comes on. It will just leave water in the bottom of the drum unless I lower the hose. Any help please?
1 Answer Check and make sure the drain hose and the tub to pump hose are not blocked or kinked. Read More...