Chip June 12, 2015 for Model Number TEDS680EQ0 As previously mentioned for this part, I tested across the blue wires, and I have continuity when I press the switch button. I also tested the thermal fuse and have continuity there. I checked the door switch and it too is working. I also tried turning the drum (to rule out starter windings of motor) while the timer was ticking (mid cycle), the door switch was closed, and the starter was pressed, also tried at start of cycle and no go. I have no fabric guard switch, only temperature control. On my timer motor, when I'm mid cycle, I can hear the timer motor running; but, the dryer doesn't start; Also, when at the start of a cycle, I can't hear the timer; and the dryer still doesn't start. What can I check next or should I replace timer. The dryer drum motor is not humming.
1 Answer Hello Chip. If the motor is not humming, then it sounds like the timer may be the issue with the unit. Read More...
Caesar November 02, 2014 for Model Number SGDS800MQ1 My gas dryer, Model SGDS800MQ1 stopped working. Based on the troubleshooting guides on your website, I replaced both the push-to-start relay (Part number AP3037944) and the Dryer Door Switch Assembly (Part Number AP3132865) but the dryer is still inoperative. I also confirmed that the thermal fuse 3392519 is good (reading 0.4 ohms on my multi-meter). Here's what it is doing now: When I push the "on" button the dryer motor does not activate and all I hear is the click of the relay. If I open the door, the interior light is illuminated and the relay clicks again (indicating that the door switch is working and cutting power to the relay). Since the interior light is illuminated with the door open and the dryer plugged in, the dryer itself is apparently getting power. Where do I go from here in terms of troubleshooting and repair? Thanks Here is the detailed information of the parts replaced so far: Relay, Push to Start Part Number: AP3037944 and Dryer Door Switch Assembly Part Number: AP3132865
1 Answer Hello Caesar, This can be the timer WP8299766, the fabric guard switch WP3405156, the motor 279827, or the harness 8299879 giving the problem. If you can tape down the door switch and reach in and turn the spin basket by hand while pressing the start button and the motor starts, the start winding in the motor has failed. If not, one of the other components has failed and should be tested with your meter to determine which part shown in the circuit on the tech sheet is at fault. Read More...
Earl June 24, 2014 for Model Number Whirpool dryer model # TEDS780-JQ0 Will a defective push-to-start switch cause my Whirlpool dryer to stop working in mid cycle?
1 Answer Hello Earl. No, it should not cause the unit to stop mid cycle. This sounds more like a thermal fuse WP3392519 or could be the door switch WP3406107. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Joe April 08, 2013 for Model Number TEDS840jQ2 Estate I tested the AP3037944 start switch like it said. I saw that the bottom two separate wires are for the buzzer. I tested the other three and got no continuity with the switch pushed over and over. I want to make sure I tested it properly. I put the alligator clip on the lower post which was a pink wire, then touched the needle to the other two posts which were blue. I got nothing for either one alone and nothing for them together. I did get continuity for the blue to blue posts. Is the switch bad? It doesn't click. It is just sort of mushy.
1 Answer Joe, If you read continuity across the Blue wire terminals on the switch, then the start switch is OK. the pink/ black wire terminal to the blue wire terminal (for the blue wire going into the cabinet, to the motor) should be the resistance of the relay in the switch. We take for granted the dryer won't start or run, and your next check should be the non resettable thermal fuse WP3392519 located on the blower housing inside the dryer. Read More...
1 Answer Mike, You will want to check the thermal fuses WP3392519 which are located on the back of the unit. The fuses should have continuity and if they do not then they need to be replaced. If the thermals are blown you will want to check to make sure that the venting from the blower assembly to the outside of the home is clean as this is the most common reason for a thermal fuse to blow.You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Pete September 16, 2012 for Model Number res7648kq0 Can you jump the switch to see if it is bad? I have power but the dryer will not start.
1 Answer Hello Pete. No, test the switch and see if it closes when you press it. If so, it is good. Make sure the thermal fuse and the door switch is good on the unit as well. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Fred June 22, 2012 for Model Number TEDS840JQ3 How to install the push to start switch p/n AP3037944?
1 Answer Hello Fred. Pull the knob off the switch and unplug the unit. Then remove the screws securing the back panel and remove the back panel. Now release the tab and twist the switch to remove it and remove the wires. Reverse the procedure to install the new switch WP3398096. Read More...
Pam September 19, 2011 for Model Number TEDS680EQ2 The on/off switch does not respond. All else seems to work. What else could be broken besides the on/off relay switch?
1 Answer Hello Pam. If everything else is working properly, and the on/off switch is not, you will need to replace the on/off switch WP3398096. Hope this helps. Read More...
Greg March 20, 2011 How do I test the AP3037944 start switch? The bottom two seperate wires are for the buzzer. I don't know how to test the other three.
1 Answer Hello Greg. If you test from pink/black to blue, with the switch pressed, you should read closed for continuity. Hope this helps. Read More...