Cesar C August 14, 2012 for Model Number mav8551aww Hey. I think I did not explain very well. But the problem with my washing machine is, it seems to be washing in the spin cycle, ie moving the blades as if washing and not turning the tub. That's why I think I'll have to replace the transmission. Is it true?. and again thanks for the attention
1 Answer Cesar, No, this does not mean you need to replace the transmission 35-6615. You do want to check or replace the "Thrust Bearing Kit "12002213and belt WP22003483.If the bearing and cams are worn out or distorted, they will not raise and unlock the brake, or lock the transmission and allow the washer tub to spin. Read More...
Cesar C August 13, 2012 for Model Number mav8551aww Hi, my washing machine on spin cycle shake. Perhaps the problem will be the transmission?. Thank you very much for the attention.
1 Answer Hello Cesar. If the unit is getting of balance and shaking bad during spin cycle, you will need to order and replace the snubber WP21002026 in the unit. Read More...
Weasel July 10, 2012 for Model Number Maytag hav2557aww My washer was not spinning the water out, it would spin, stop, start over again. I replaced the thrust bearing, it seems a little better but now the tub wants to spin during the wash cycle. When I turn the pulley counterclock wise the brake doesnt release, and the shaft spins freely. Any more suggestions?
1 Answer Weasel, a new brake rotor WP35-6714 may be a good idea, you also want to clean up the internal surface of the stator WP35-6918 with emory cloth and wash out the assembly with rubbing alcohol. You also want to clean and lubricate the splines on the rotor, so it moves freely on the transmission case. You also want to order additional washers WP35-2082 and WP35-2132 to achieve the proper tolerances when you re install the thrust bearing kit ( you may need to add or swap) thick vs thin washers,etc. In order to remove the brake stator, you will need to purchase a brake removal tool 12002012 , or take one of the screws out of the stator assembly and take it to a hardware store and purchase two screws the same size and thread pattern, but 2 to 3 inches long, so you can remove the stator safely. Read More...
Jobob May 16, 2012 for Model Number mav9501eww When I took apart my washer to examine why the brake was not engaging the brake lining of the brake rotor came off. Is this supposed to happen or is the brake rotor and lining one unit. Just wondering if I should purchase a new unit(rotor).
1 Answer Hello Jobob. No, based on the information you provided, you will need to order and replace the rotor WP35-6714, stator WP35-6918, and the snubber WP21002026. Read More...
Dale February 15, 2012 for Model Number mav2755aww In the spin cycles my washer drum spins slowly, speeds up, then stops and does this over and over. The clothes are still wet from not being spun enough. It makes a knocking sound each time it stops. I replaced the thrust bearing with a new kit. The clip only installs with the thin washer that was provided. There has been no change after the new thrust bearing was installed. Before and after the thrust bearing replacement when checking under the washer and manually turning the thrust bearing pulley the following occurs. When turning clockwise the agitator turns. when turning counter clockwise the agitator turns and the brake does not disengage. When someone holds the agitator and prevents it from turning and the pulley below is turned counter clockwise the brake disengages and the tub begins to spin. I assume nothing is wrong with the thrust bearing assembly now. I assume the brake should disengage easily and that the brake rotor should slide up and down easily on the splined shaft. There is no way to adjust the thrust washer with any other size washer than the small one provided, which is the same size as the original washer. The washer is 5 years old. I removed and cleaned the brake rotor and stator. There is about 1/16 thickness left on the brake lining. I am assuming the brake rotor is worn and not sliding up and down easily on the splined shaft which is causing the brake to release later and harder than it should. Am I correct in assuming I need to replace the brake rotor and stator?
1 Answer Hello Dale. No, you will need to use a screwdriver and pull out on the shaft and install the thrust bearing 12002213 with the thick washer, or may be even use both washers to repair the unit. Hope this helps. Read More...
William B. January 10, 2012 for Model Number MAV9504eww Maytag Washer My Brake Roto AP4373023, Brake Spring AP4024479, Brake Stator AP4045273 and Snubber AP4024496 are going to be replaced. The problem is that I don't know what grease to use on the Brake Roto center spline or what grease to use on the Thrust Bearing (AP4009132 - I'm reusing the original part). Thanks Bill
1 Answer Hello William. You can use the center seal grease WPY056016 for the repair. Hope this helps. Read More...
Alfredo I August 24, 2011 for Model Number aav7000aww my washer dont move in washing cycle but in spin cycle it does.
1 Answer Alfredo, I don't think you will need a brake rotor, you may need a thrust bearing kit 12002213 or a new transmission 35-6615 . You may want to lean the washer against the wall or lay the washer on it's back, remove the belt and the thrust bearing pulley and washer assembly,and check it for excess wear and tear or the cam and pulley for deformation, You can carefully use a pair of pliers or vice grips and turn the shaft by hand, the clockwise direction should be the agitate mode, and the agitator should move back and forth, if the gears are OK. If tghe agitator does not move or the gears lock up and you can't turn the shaft you have a bad transmission. Good Luck and Thanks. Read More...
Tooloose July 02, 2011 for Model Number MAV6200AWW How do I change the snubber and brake roto? Loud squeel at the end of cycle. I changed the thrust bearing and checked the alignment marks and they only line up without any spacers, but doesn't spin. I put the thin spacer in and it works, but is beyond the alignment marks and still squeels at the end.
1 Answer Hello Tooloose. Here are the instructions from the manufacture. Hope this helps.1. Disconnect the power to the unit.2. Remove the drive pulley and cam components from the unit.3. Use the brake tool TJ12002011 as follows:Pull out and remove the "U" retainer from tool.Slip the splined end of the drive shaft into hole located in the tool inner plunger.Looking at the side of the tool, align slots on tool barrel and holes in tool plunger between splines and chamfered shoulder of shaft.Slip "U" retainer through tools slots and holes capturing the drive shaft behind the chamfered shoulder.Tighten tool nut to compress brake spring until transmission turns freely.Remove 6 screws which secure the brake stator and snubber to the underside of the suspension housing.Loosen tool nut until the brake spring reaches its free length.Remove "U" retainer from tool and remove tool from drive shaft.Remove brake components.You can install the snubber at this time.Reinstall in reverse order. Read More...
Doug April 19, 2011 for Model Number mavt446aww Thanks for the reply. Second question is there a release spring or mechanism that enables the brake to fuction properly? It seems like mine is engaged alll the time. I only ask in case there is anything else that I need to get.
1 Answer Hello Doug. The part that releases the brake is the thrust bearing 12002213. The brake should be engaged at all times, except for the spin cycle. Hope this helps. Read More...
Doug April 19, 2011 for Model Number mavt446aww When my wife runs the washer on delicate cylce, perfect. On regular it "screeches" like a bad bearing, when the inner tub rotates it 1/8 turn, after the agitator completes it's portion. Have replaced the innet tub bearing, no change. Could I have a brake/rotor issue/ broken brake spring?
1 Answer Hello Doug. It sounds like you will need to replace the brake WP35-6714, stator WP35-6918, and the snubber WP21002026. If they are bad, they can cause the problems your having. Hope this helps. Read More...