Cynthia March 23, 2013 Why is the machine stuck on spin. It will not start at all. Maytag Centennial top load.
1 Answer Hello Cynthia. Check and see if the lid switch is bad on the unit. Also, make sure there is power coming to the washer. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Miguel R January 19, 2013 for Model Number whirlpool washer wtw57esvw Hi, when I turn on my washer I only get hot water even in the cold position Thank you
1 Answer Hello Miguel, You will want to check your water temperature thermistor. At 77 degrees it should read between 49 and 51kohms. If not reading this then the thermistor is faulty and needs to be replaced. Read More...
Jeff B. January 03, 2013 for Model Number WTW57ESVH0 When I turn the timer over to begin the cycle, the agitator begins agitating before any water starts filling. The water will fill to the appropriate level, but the agitator will agitate while this is filling. Do I need the temperature switch or does it go through the timer first? Or could it be the water level sensor?
1 Answer Hello Jeff. Based on the information you provided, you will need to order and replace the sensor switch WPW10292584 and the timer WPW10177827 on the unit. Read More...
Albert July 06, 2012 for Model Number WTW57ESVW0 I have a whirlpool washer and the tub will not fill with water. It does not agitate. It will, however spin. Also if I fill the tub with using a pail the water will drain. I replaced the timer switch but that did not work. I appreciate any help you can provide.
1 Answer Hello Albert. Based on the information you provided, it sounds like the sensor switch WPW10292584 is bad and will need to be replaced in the unit. If this switch is bad, it will prevent water from filling into the unit. Read More...
Willard June 14, 2012 for Model Number WTW53ESVWO I am getting hot water when I select cool, and hot when I select tap cold. I checked cold water inlet screen and it is clean. I blocked in hot water supply and I get no water in cool or cold setting. Is it my atc switch auto load switch or water valve, or flow switch?
1 Answer Hello Willard, This is most likely the cold water inlet valve. The ATC could be defective, but is less often the issue. I doubt the flow switch is the issue as it monitors the hot water inlet also. Read More...
Sokea May 18, 2012 for Model Number MVWC6ESWW0 As I turn the machine on, I have no cold, warm, or hot water come in at all. I measured the voltage at the terminal of water inlet valve, both terminals did not have 120 vac present. Is this problem can cause by water temperature switch? Please help. Thank you, Sokea
1 Answer Hello Sokea. No, based on the information you provided, the sensor switch WPW10292584 is bad and will need to be replaced. Read More...
Jim December 19, 2011 for Model Number mvwc6eswwo At the start of the cycle water comes in an the agitator also starts. Could the temp switch cause this problem?
1 Answer Hello Jim. Based on the information you provided, the timer WPW10243947 and the sensor switch WPW10292584 will need to be replaced to repair the issue. The timer is the agitation and the sensor switch is the water. These work together and will cause this issue. Hope this helps. Read More...
1 Answer Hello Nicole. You will need to disconnect the power to the unit. The use a flat blade putty knife and release the tabs under the front corners of the control panel and flip the control panel backwards. Remove the knob and the wires from the switch. Release the tab on the switch and twist the switch to remove it. Reinstall with the new temperature switch WPW10179666 in reverse order. Hope this helps. Read More...
Blaine June 10, 2011 for Model Number wtw57esvwo Is this the same for the water level switch? I have part number ap4459660, but I cant place where it goes.
1 Answer Hello Blaine! No, part number WPW10179666 is the water temperature switch. For the water level switch you will need part number WPW10292584. Thanks! Read More...