Brian F. July 26, 2012 for Model Number ade7000ayw I just replaced the thermal fuse (p/n AP4056527) on my dryer. Less than three days later it is bad again. The vent hose is not blocked, vent wheel is not spinning on motor shaft and verified that it is the correct fuse. Why is it blowing fuses. I have a new fuse on order. Thanks. Read more: http://www.appliancepartspros.com/Appliance-Parts/whirlpool-fuse--thermal-item-number-ap4056527.aspx#ixzz21ktNmSJw http://www.appliancepartspros.com
1 Answer Hello Brian, I certainly don't want to make you mad, but the thermal fuse is opened by temperature. Nothing else will open it. This is a clear indication that somehow there is too much heat being held inside the unit. If you have flexible ducting, there could be a crimp when the unit is pushed back to the wall. Remember if the duct is in excess of the equivalent of 25 feet long, (each 90° angle is the equivalent to 6 feet of straight ducting), the unit will blow the heat, lint, and moisture past the felt drum seals back into the cabinet with the thermal fuse, thermal cutout, and thermostats. Everything you don't want heat, lint, and moisture on will get heat, lint, and moisture on it. Another possibility is if your laundry room has a door, it may not be getting enough air intake. This decreases the air flow just like restricting the exhaust will decrease it. If this is the case, you either need a louvered door, or simply leave the door open. In either case, the issue has to be air flow because, as previously stated, the thermal fuse is opened thermally which means it is getting too hot. Read More...
1 Answer Hello Lb. Test the thermal fuse WP53-1182 and make sure it reads closed for continuity. If not, it will cause the issue you are having. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Barry M. January 24, 2012 for Model Number HYE3657AYW The driver just quit. This morning I noticed that the bulb was very dim. When I tried to turn the dryer on nothing happened. I have checked the house circuit breaker and the plug on the driver both have juice. Is there something on the dryer that would just make it stop? The vent is not clogged.
1 Answer Hello Barry. Yes, test the thermal fuse WP53-1182 and make sure it reads closed. It is located on the side of the heater housing and will have 2 white wires going to it. If it is good, check and make sure the door switch is working properly. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Eric November 12, 2011 for Model Number pyet244ayw For WHIRLPOOL Fuse, Thermal (Part Number: AP4056527 How do I get the old fuse out?
1 Answer Hello Eric. You will need to remove the thermostat off the top of the heater. Then remove the heater from the housing. Once removed, you can lift the bracket on the side of the housing upward and remove the thermal fuse. Replace the fuse WP53-1182 in reverse order. Hope this helps. Read More...
Jody November 09, 2011 for Model Number ade7000ayw The thermal fuse part for this model does not match the old one. What should I do?
1 Answer Hello Jody. Based on the model number you provided, WP53-1182 is the correct thermal fuse. It is located on the air duct assembly and should install properly. Hope this helps. Read More...