Juan July 30, 2020 for Model Number MAV7600AWW When set on cold/cold I get warm water. On all settings where cold water is requested the water comes out warm.
1 Answer Juan, my bet is on the water valve! This model of washer has a valve with a thermistor to assure water temp correctness. The tech sheet located in the washer will give you the values to measure for that thermistor. The water valve is part [12002158]. Thanks for the question. Read More...
Darryl C. October 06, 2014 for Model Number MAV7358AWW This 11 year old washer has recently begun to intermittently feed warm or hot water during the wash or rinse cycle regardless of temperature setting. It is happening more frequently than not. Once this occurs, pushing any of the temperature buttons will not change the temperature. What's the problem and what parts do I need to fix it?
Ed Hatfield May 11, 2013 for Model Number mav6300aww My washing machine will not allow any water to enter the washing machine when I have it on the Hot Water Wash / Cold Water Rinse setting. The other three settings Warm/Warm, Warm/Cold and Cold/Cold all allow "cold water only" into the machine. I have doubled checked my Hot Water feed into the washer and hot water definitely is coming to the washer. Could the temperature switch be bad? Bad water valve? Thanks.
1 Answer Ed, you most likely have an issue with the water valve WP22002707 water temperature switches are not that common an issue. Read More...
Laura L October 16, 2012 for Model Number MAV7600AW Cold water will not run into washer, hot will. I have already replaced the inlet valve, still doesn't work. Do I need to replace the temp switch?
1 Answer Hello Laura. Check for a wiring issue first. If none is found, then you will test the temp switch for continuity. If it checks bad, replace it. If it checks good, you may need to replace the timer on the unit. Read More...
Dwayne August 13, 2011 for Model Number MAV7650AWW I cannot get the water/rinse temp to change. Is this because the temp switch is bad or is this something else, like the analogue control board or water valve? Note, the tank fills to correct water level for washing.
1 Answer Hello Dwayne. This unit uses a thermistor in the water valve 12002158. It distributes the water temperature according to the setting. You will need to test and see if there is power going to the hot water valve, when the machine is set on rinse. If not, and the hot water is coming in, you will need to replace the water valve. If there is power to the hot valve on a cold rinse, you will need to replace the temperature switch WP22002999. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Bob E. June 27, 2011 for Model Number MAV 7600 AWW I wish to remove the 4 button tempreature switch. I looked it over yesturday and could not get it out. What am I missing?
1 Answer Hello Bob. You will need to remove the three screws across the back of the control panel. Then rock the panel forward and lift the control panel out of the top of the unit. Now you can access the switch. You will need to unplug the wires going to the switch and install them onto the new switch. Remove the old switch and install in reverse order with the new switch. Hope this helps. Read More...
Patrick D. April 10, 2011 for Model Number mav6257aww On the water selector the cold cold button on the selector doesn't work but the other selections do. Does that mean the whole selector is bad?
1 Answer Hello Patrick! Is cold water coming into the unit on the other cycles? If not, you will need to replace the water valve. If it is, then you will need to replace the switch. We will need your appliance serial number to verify the correct part numbers as there is a series change. Thanks. Read More...