Anne August 26, 2013 for Model Number Inglis Hi, I have an Inglis smooth top range & the DUAL heating element is staying on high, I took a picture of the switch for this element and it is solid blue with the following written on it 9761048, P1 top right, P2 S2, bottom right. The reason I question if this is the right part for my stove is because in the video your switch is white with a piece of visible metal that looks just like the other 3 remaining burner switches on my stove. My dual burner temp control switch is a solid blue box with no visible metal. Do you sell a temp control switch that will work for my stove. Thank You
1 Answer Anne, to verify the parts used on your appliance we'll need the appliance model number. The video listed for the infinite switch part number WP9761048 is there to show you the general installation of infinite switches. Your part and appliance model will differ due to the make and model. Thanks. Read More...
Eric July 21, 2013 for Model Number GR445LXMS Does this part replace the left front (dual) burner for this model? This is where you can either set a inner burner on or both inner and outer burner. It would appear that the burners only stay on high setting. This is the part I would need to fix it correct? Thanks
Craig June 21, 2013 for Model Number RF198LXMB I have a Whirlpool free standing stove RF198LX MB that needs to have the dual burner switch replaced. What is the part number for this surface unit switch? Thank you, Craig
1 Answer Craig, The infinite switch for the left front dual element is part number WP9761048. Read More...
Sue March 07, 2013 for Model Number whirlpool gr460LXLP0 Having a "hot" problem with front left burner (dual heat) - could be burner (how to open the top?) or the switch p/n 8522887. However, I don't know if wires to switch were connected properly, or how to test this switch - the tests I found all indicated for H or L, my switch has P and S...Can you tell me: 1. how to open top of stove to get to burners? 2. wiring diagram or schematic for this switch (missing from back of stove) 3. how to test if switch is bad. Thanks much.
1 Answer Sue, To access the top burner assembly, when you open the oven door, on either side there will be a screw that holds the main top in place or they may be on the upper part of opening. You would take screws out and you can lift top. To check the switches, S2 goes to the inner element, 4a goes to the outer element and 2 is the common side. Read More...
Barn November 21, 2012 for Model Number ftq386fwux My 2 large front burners stucks on high. Can not adjust the temperature. Is the switch bad? Do both use the same switch? One is a 3 ring burner, and one is 2 ring burner.
1 Answer Barn, You're on track, Depending on the type of infinite switch in the range, the H2 to L2 circuit cycles during the use of the burner, as the heat control, You most likely have a faulty infinite switch, if the burner is "stuck" on the high setting. Unfortunately,we are unable to research your parts needs, or wiring information, the model number you supplied is incorrect. Read More...
Joe February 12, 2012 for Model Number gr475lxms My left front dual burner comes on and stays on what is the part # I will need and how is it installed?
1 Answer Hello Joe. Based on the information you provided, it sounds like the switch WP9761048 is bad and will need to be replaced. You will need to disconnect the power and remove the knob off the switch. Then remove the two screws holding the switch in place. Remove the back panel to access the switch. Unplug the wires and connect them to the correct location on the new switch. Install the new switch in reverse order. Hope this helps. Read More...
Frank P. August 31, 2011 for Model Number RF378LXMO Sorry, I misspelled the model no on my first question. I need a new switch for the dual range burner. The P/N on the old switch is 8522887 or possibly 8522687. Difficult to read.
1 Answer Hello Frank. Based on the model number you provided, WP9761048 is the correct switch for the dual element. Hope this helps. Read More...
Frank P. August 30, 2011 for Model Number RF378LZMO Is this the switch that controls the dual element burner on this range?
1 Answer Hello Frank. The model number you provided is not working. Can you check and make sure the model number is correct? Thanks. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Erich August 23, 2011 for Model Number GR445LXLS My stove has GR445LXLS listed on its label, but this and other sites resolve it to GR445LXLS0 (or GR445LXLSO) and I was wondering if AP3777761 is still the right part for the left-front (Accusimmer) burner?
1 Answer Hello Erich! Yes, the left front burner switch is part number WP9761048. Thanks! Read More...
1 Answer Linda, if your accusimmer burner is the front left burner the matching knob will be WP9761048. Thanks! Read More...