Bernie August 21, 2017 for Model Number ED25QFXHB00 I'm beginning to dispair! Trying to replace the Defrost Timer on my Whirlpool ED25QFXHB00 refrigerator with a W10822278 timer, but cannot track down a wiring diagram to know which pin to put the loose wire on. Hopefully you know :-)
1 Answer Hello Bernie! The orange wire should go to pin 1, red to pin 4, pink to in 2 and white to pin 3. Hopefully this helps! Read More...
Clay August 18, 2017 for Model Number 106.62852100 I'm changing my defrost timer and need to know if the black loose wire goes on #1 or #2 terminal. Thanks, Clay
Jay July 23, 2017 for Model Number RT21LMXJW01 I have replaced with new timer and have placed black wire on #1. I went through and manually turned timer. The refrigerator wants to turn in but then stops I also noticed new defrost timer was getting warn. What to do? Did I do something wrong?
1 Answer Jay, You will need to rewire the new timer. You have a "version 2 " Cumulative compressor run application. For cumulative run timer push slotted loose timermotor lead over & all the way down terminal number 2 with wire toward timer motor. Check and make sure the colored wires are attached to the proper terminals 1 – Black Wire 2 – Pink Wire 3 – Red Wire 4 – Orange Wire. When wired correctly to a refrigerator’s accumulated run clock, replacement timer will provide defrost every 8 hours of compressor run time after the bimetal closes. Defrost timer motors can and do get warm/hot, but the timer motor will advance and start the cooling mode in 20 to 30 minutes after the start of the defrost cycle. Read More...
Gene July 18, 2017 for Model Number 106.628260 Sears Coldspot Freezer bought in 1968 Do not have wiring diagram and don't know which Terminal to connect the Black wire too.
1 Answer Hello Gen. You will need to connect the wire to the number 2 terminal of the timer. Read More...
Gary July 12, 2017 for Model Number Kenmore 106.59582990 Need help don't have a wiring sheet to know which pin the black wire on defrost timer. Thanks
1 Answer Gary, The black wire will go over terminal number 1 on the new timer then connect the wire harness to it. Read More...
Joe July 11, 2017 for Model Number ED22TEXHW00 Which terminal, 1 or 2, does the black wire go on a replacement defrost timer w10822278?
1 Answer Hello Joe. The wire will need to be placed onto terminal number 2 of the timer. Thanks. Read More...
Pat July 06, 2017 for Model Number M4TXNWFYW00 The defrost timer is bad and I don't know if it is a Continuous run application or a Cumulative compressor run application
1 Answer Hello Pat. For the model number you provided, you will need to install the black wire onto terminal number 2 of the timer. Thanks. Read More...
George June 28, 2017 for Model Number ED22TEXHW01 Hi! I've replaced my defrost timer (483212) on my Whirlpool, and seems to work just fine! Put the jumper on the correct pin as with my old timer. My issue is that every few days, my coils freeze over and stop the fan from spinning that blows cool air into the fridge. When I advance the defrost timer using the dial, it clicks into the defrost mode, and I can see/feel heat from the heating element. I've also checked the defrost thermostat with a multimeter, and I am seeing continuity. I've also cleaned the coils underneath the fridge as well. However, it seems like my freezer is just getting too cold still or is not defrosting enough. I replaced the timer with the same timer as I had before, which worked great for 10 years, but now I'm seeing this issue with the coils not defrosting every few days now. Any ideas why this could be?
1 Answer George, This issue sounds likely that the timer received is sticking and not allowing the unit to into the defrost cycle and would need to replace the timer. Read More...
Breanna May 30, 2017 Where to put black wire? Whirlpool Designer Style. Model # ET22DMFXN00. mf 92_97. Serial #E00912114. No manual and won't come up on whirlpool site. Help me.
1 Answer Hello Breanna. You will place the black wire onto terminal number 2 of the timer. Thanks. Read More...
Bruce May 03, 2017 The defrost timer has been in for 3 days and it will only advance into defrost if done manually. the black wire is on terminal 2
1 Answer Bruce, It sounds like you may have the black wire on the wrong terminal and should be on terminal number 1. Read More...